W jądrze 2.6.32.2 próbuje załadować moduł acpi_cpufreq i dostaję:
Kod: Zaznacz cały
FATAL: Error inserting acpi_cpufreq (/lib/modules/2.6.32.2/kernel/arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.ko): No such device
Nie można za
Nie moŻna załadować modułu acpi_cpufreq - 2.6.32.2
Witam.
W jądrze 2.6.32.2 próbuje załadować moduł acpi_cpufreq i dostaję:
Jak załadować ten moduł?
W jądrze 2.6.32.2 próbuje załadować moduł acpi_cpufreq i dostaję:
Za mało informacji, pokaż wynik
Kod: Zaznacz cały
modprobe -v acpi-cpufreqKod: Zaznacz cały
modprobe -v acpi-cpufreqKod: Zaznacz cały
insmod /lib/modules/2.6.32.2/kernel/arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.ko
FATAL: Error inserting acpi_cpufreq (/lib/modules/2.6.32.2/kernel/arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.ko): No such device
i jeszcze wynik
Kod: Zaznacz cały
lsmodPolecenie:
dostarcza informacji:
Kod: Zaznacz cały
lsmodKod: Zaznacz cały
Module Size Used by
uinput 5793 1
radeon 521666 2
ttm 30669 1 radeon
drm_kms_helper 21955 1 radeon
drm 126812 5 radeon,ttm,drm_kms_helper
i2c_algo_bit 4219 1 radeon
ppdev 4754 0
lp 6905 0
parport 26447 2 ppdev,lp
sco 6924 2
bridge 40937 0
stp 1140 1 bridge
bnep 8476 2
rfcomm 29673 0
l2cap 29677 6 bnep,rfcomm
crc16 1063 1 l2cap
bluetooth 44429 6 sco,bnep,rfcomm,l2cap
cpufreq_stats 3149 0
cpufreq_powersave 742 0
cpufreq_conservative 5132 0
ipv6 222201 14
af_packet 15110 2
ntfs 202205 1
nls_utf8 960 2
nls_cp437 4545 1
vfat 8028 1
fat 42960 1 vfat
fuse 50636 1
dm_crypt 10290 0
snd_hda_codec_si3054 3030 1
snd_hda_codec_realtek 178081 1
snd_hda_intel 17904 1
snd_hda_codec 47783 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 4910 1 snd_hda_codec
joydev 7704 0
snd_pcm_oss 33085 0
snd_mixer_oss 14202 1 snd_pcm_oss
arc4 1058 2
ecb 1577 2
snd_pcm 56005 4 snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss
b43 137119 0
snd_seq_dummy 1035 0
snd_seq_oss 24184 0
snd_seq_midi 4040 0
rng_core 2570 1 b43
snd_rawmidi 15304 1 snd_seq_midi
mac80211 120442 1 b43
snd_seq_midi_event 4484 2 snd_seq_oss,snd_seq_midi
snd_seq 40580 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
cfg80211 105232 2 b43,mac80211
snd_timer 15733 2 snd_pcm,snd_seq
snd_seq_device 4313 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
rfkill 12320 3 bluetooth,cfg80211
i2c_piix4 7472 0
psmouse 36645 0
i2c_core 14920 4 radeon,drm,i2c_algo_bit,i2c_piix4
shpchp 26752 0
serio_raw 3620 0
snd 42174 15 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel,snd_
hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pcspkr 1347 0
pci_hotplug 23172 1 shpchp
evdev 6842 16
rtc_cmos 7536 0
led_class 1965 1 b43
soundcore 5007 1 snd
video 14935 0
rtc_core 10913 1 rtc_cmos
snd_page_alloc 5777 2 snd_hda_intel,snd_pcm
output 1404 1 video
rtc_lib 1513 1 rtc_core
processor 25822 1
ac 2127 0
battery 6105 0
button 3702 0
ext3 110690 2
jbd 38842 1 ext3
mbcache 4310 1 ext3
dm_mod 51350 1 dm_crypt
usbhid 32427 0
hid 60349 1 usbhid
sg 23415 3
sr_mod 12937 0
cdrom 30409 1 sr_mod
sd_mod 26597 5
ata_generic 2235 0
pata_acpi 2264 0
usb_storage 33206 0
pata_atiixp 2689 0
ohci_hcd 19476 0
ahci 28841 6
ehci_hcd 30986 0
ssb 35860 1 b43
pcmcia 19862 2 b43,ssb
pcmcia_core 25515 3 b43,ssb,pcmcia
libata 133914 4 ata_generic,pata_acpi,pata_atiixp,ahci
usbcore 118629 5 usbhid,usb_storage,ohci_hcd,ehci_hcd
nls_base 5197 6 ntfs,nls_utf8,nls_cp437,vfat,fat,usbcore
scsi_mod 118999 5 sg,sr_mod,sd_mod,usb_storage,libata
ati_agp 4614 0
thermal 9390 0
fan 2630 0
Jak dla mnie to błąd w jądrze. Pokaż jeszcze: albo i cały dmesg.
Kod: Zaznacz cały
dmesg |grep -i acpiWynik dmesg:
Kod: Zaznacz cały
Initializing cgroup subsys cpuset
Linux version 2.6.32.2 (root@siduxbox) (gcc version 4.4.2 (Debian 4.4.2-7) ) #1 SMP PREEMPT Tue Dec 29 17:54:44 CET 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000037fa0000 (usable)
BIOS-e820: 0000000037fa0000 - 0000000037fae000 (ACPI data)
BIOS-e820: 0000000037fae000 - 0000000037ff0000 (ACPI NVS)
BIOS-e820: 0000000037ff0000 - 0000000038000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
DMI 2.4 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x37fa0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FC0000000 write-back
1 base 040000000 mask FF0000000 write-back
2 base 050000000 mask FF8000000 write-back
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
initial memory mapped : 0 - 00800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 3786a000 - 37f8fe74
Allocated new RAMDISK: 005a0000 - 00cc5e74
Move RAMDISK from 000000003786a000 - 0000000037f8fe73 to 005a0000 - 00cc5e73
ACPI: RSDP 000f8070 00014 (v00 ACPIAM)
ACPI: RSDT 37fa0000 00040 (v01 _ASUS_ Notebook 12000721 MSFT 00000097)
ACPI: FACP 37fa0200 00084 (v02 A_M_I_ OEMFACP 12000721 MSFT 00000097)
ACPI: DSDT 37fa0630 07590 (v01 A0669 A0669000 00000000 INTL 20060113)
ACPI: FACS 37fae000 00040
ACPI: APIC 37fa0390 0005C (v01 A_M_I_ OEMAPIC 12000721 MSFT 00000097)
ACPI: MCFG 37fa03f0 0003C (v01 A_M_I_ OEMMCFG 12000721 MSFT 00000097)
ACPI: SLIC 37fa0430 00176 (v01 _ASUS_ Notebook 12000721 MSFT 00000097)
ACPI: BOOT 37fa0600 00028 (v01 A_M_I_ OEMBOOT 12000721 MSFT 00000097)
ACPI: OEMB 37fae040 0005B (v01 A_M_I_ AMI_OEM 12000721 MSFT 00000097)
ACPI: SSDT 37fa7bc0 001EF (v01 AMI CPU_CST 00000001 INTL 20060113)
ACPI: Local APIC address 0xfee00000
7MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 000059c564] TEXT DATA BSS ==> [0000100000 - 000059c564]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [000059d000 - 000059f1ea] BRK ==> [000059d000 - 000059f1ea]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00005a0000 - 0000cc5e74] NEW RAMDISK ==> [00005a0000 - 0000cc5e74]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00ff780] ff780
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x00037fa0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x00037fa0
On node 0 totalpages: 229167
free_area_init_node: node 0, pgdat c04cc8c0, node_mem_map c1001200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 16 pages used for memmap
HighMem zone: 1938 pages, LIFO batch:0
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 1 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 38000000 (gap: 38000000:c6e00000)
NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 14 pages/cpu @c1800000 s33336 r0 d24008 u2097152
pcpu-alloc: s33336 r0 d24008 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227375
Kernel command line: root=UUID=f75eddba-c5da-404c-9aa2-392b5c45cdfb ro quiet vga=791
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:00037fa0)
Memory: 896152k/917120k available (2786k kernel code, 20172k reserved, 1130k data, 372k init, 7816k highmem)
virtual kernel memory layout:
fixmap : 0xfff91000 - 0xfffff000 ( 440 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc04d4000 - 0xc0531000 ( 372 kB)
.data : 0xc03b8a8a - 0xc04d3488 (1130 kB)
.text : 0xc0100000 - 0xc03b8a8a (2786 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:320
Console: colour dummy device 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1596.067 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3192.13 BogoMIPS (lpj=1596067)
Security Framework initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring handled by SMI
using mwait in idle threads.
Performance Events: Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Celeron(R) M CPU 520 @ 1.60GHz stepping 06
Brought up 1 CPUs
Total of 1 processors activated (3192.13 BogoMIPS).
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=8
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Executed 2 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:12.0: reg 10 io port: [0xe800-0xe807]
pci 0000:00:12.0: reg 14 io port: [0xe400-0xe403]
pci 0000:00:12.0: reg 18 io port: [0xe000-0xe007]
pci 0000:00:12.0: reg 1c io port: [0xdc00-0xdc03]
pci 0000:00:12.0: reg 20 io port: [0xd800-0xd80f]
pci 0000:00:12.0: reg 24 32bit mmio: [0xfebffc00-0xfebfffff]
pci 0000:00:12.0: set SATA to AHCI mode
pci 0000:00:13.0: reg 10 32bit mmio: [0xfebfe000-0xfebfefff]
pci 0000:00:13.1: reg 10 32bit mmio: [0xfebfd000-0xfebfdfff]
pci 0000:00:13.2: reg 10 32bit mmio: [0xfebfc000-0xfebfcfff]
pci 0000:00:13.3: reg 10 32bit mmio: [0xfebfb000-0xfebfbfff]
pci 0000:00:13.4: reg 10 32bit mmio: [0xfebfa000-0xfebfafff]
pci 0000:00:13.5: reg 10 32bit mmio: [0xfebff800-0xfebff8ff]
pci 0000:00:13.5: supports D1 D2
pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.5: PME# disabled
pci 0000:00:14.0: reg 10 io port: [0xb00-0xb0f]
pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
pci 0000:00:14.1: reg 20 io port: [0xff00-0xff0f]
pci 0000:00:14.2: reg 10 64bit mmio: [0xfebf4000-0xfebf7fff]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
pci 0000:01:05.0: reg 10 32bit mmio pref: [0xa0000000-0xafffffff]
pci 0000:01:05.0: reg 14 io port: [0x9800-0x98ff]
pci 0000:01:05.0: reg 18 32bit mmio: [0xfa8f0000-0xfa8fffff]
pci 0000:01:05.0: reg 30 32bit mmio pref: [0xfa8c0000-0xfa8dffff]
pci 0000:01:05.0: supports D1 D2
pci 0000:00:01.0: bridge io port: [0x9000-0x9fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfa800000-0xfa8fffff]
pci 0000:00:01.0: bridge 32bit mmio pref: [0x9ff00000-0xbfefffff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xfa9fc000-0xfa9fffff]
pci 0000:02:00.0: supports D1 D2
pci 0000:00:04.0: bridge 32bit mmio: [0xfa900000-0xfa9fffff]
pci 0000:00:05.0: bridge io port: [0xa000-0xbfff]
pci 0000:00:05.0: bridge 32bit mmio: [0xfaa00000-0xfe9fffff]
pci 0000:00:05.0: bridge 64bit mmio pref: [0xbff00000-0xdfefffff]
pci 0000:06:00.0: reg 10 64bit mmio: [0xfeac0000-0xfeafffff]
pci 0000:06:00.0: reg 30 32bit mmio pref: [0xfeaa0000-0xfeabffff]
pci 0000:06:00.0: PME# supported from D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:00:06.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci 0000:00:14.4: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 7 10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12) *0, disabled.
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:05: ioport range 0x40b-0x40b has been reserved
system 00:05: ioport range 0x4d6-0x4d6 has been reserved
system 00:05: ioport range 0xc00-0xc01 has been reserved
system 00:05: ioport range 0xc14-0xc14 has been reserved
system 00:05: ioport range 0xc50-0xc51 has been reserved
system 00:05: ioport range 0xc52-0xc52 has been reserved
system 00:05: ioport range 0xc6c-0xc6c has been reserved
system 00:05: ioport range 0xc6f-0xc6f has been reserved
system 00:05: ioport range 0xcd0-0xcd1 has been reserved
system 00:05: ioport range 0xcd2-0xcd3 has been reserved
system 00:05: ioport range 0xcd4-0xcd5 has been reserved
system 00:05: ioport range 0xcd6-0xcd7 has been reserved
system 00:05: ioport range 0xcd8-0xcdf has been reserved
system 00:05: ioport range 0x800-0x89f has been reserved
system 00:05: ioport range 0xb00-0xb1f could not be reserved
system 00:05: ioport range 0x900-0x90f has been reserved
system 00:05: ioport range 0x910-0x91f has been reserved
system 00:05: ioport range 0xfe00-0xfefe has been reserved
system 00:05: ioport range 0x4000-0x40fe has been reserved
system 00:05: iomem range 0xfed45000-0xfed89fff has been reserved
system 00:05: iomem range 0xffb80000-0xffbfffff has been reserved
system 00:05: iomem range 0xfff80000-0xffffffff has been reserved
system 00:08: ioport range 0x250-0x253 has been reserved
system 00:08: ioport range 0x256-0x25f has been reserved
system 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0a: iomem range 0x0-0x9ffff could not be reserved
system 00:0a: iomem range 0xc0000-0xcffff could not be reserved
system 00:0a: iomem range 0xe0000-0xfffff could not be reserved
system 00:0a: iomem range 0x100000-0x37ffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x9000-0x9fff
pci 0000:00:01.0: MEM window: 0xfa800000-0xfa8fffff
pci 0000:00:01.0: PREFETCH window: 0x9ff00000-0xbfefffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: 0xfa900000-0xfa9fffff
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: 0xa000-0xbfff
pci 0000:00:05.0: MEM window: 0xfaa00000-0xfe9fffff
pci 0000:00:05.0: PREFETCH window: 0x000000bff00000-0x000000dfefffff
pci 0000:00:06.0: PCI bridge, secondary bus 0000:06
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:07
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:14.4: PCI bridge, secondary bus 0000:08
pci 0000:00:14.4: IO window: disabled
pci 0000:00:14.4: MEM window: disabled
pci 0000:00:14.4: PREFETCH window: disabled
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
pci_bus 0000:01: resource 1 mem: [0xfa800000-0xfa8fffff]
pci_bus 0000:01: resource 2 pref mem [0x9ff00000-0xbfefffff]
pci_bus 0000:02: resource 1 mem: [0xfa900000-0xfa9fffff]
pci_bus 0000:03: resource 0 io: [0xa000-0xbfff]
pci_bus 0000:03: resource 1 mem: [0xfaa00000-0xfe9fffff]
pci_bus 0000:03: resource 2 pref mem [0xbff00000-0xdfefffff]
pci_bus 0000:06: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:08: resource 3 io: [0x00-0xffff]
pci_bus 0000:08: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:01:05.0: Boot video device
Unpacking initramfs...
Freeing initrd memory: 7319k freed
Simple Boot Flag at 0xff set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1262343706.485:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1750
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:04.0: irq 24 for MSI/MSI-X
pcieport 0000:00:04.0: setting latency timer to 64
pcieport 0000:00:05.0: irq 25 for MSI/MSI-X
pcieport 0000:00:05.0: setting latency timer to 64
pcieport 0000:00:06.0: irq 26 for MSI/MSI-X
pcieport 0000:00:06.0: setting latency timer to 64
pcieport 0000:00:07.0: irq 27 for MSI/MSI-X
pcieport 0000:00:07.0: setting latency timer to 64
vesafb: framebuffer at 0xa0000000, mapped to 0xf8080000, using 3072k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:519f
vesafb: pmi: set display start = c00c520d, set palette = c00c5247
vesafb: pmi: ports = 9810 9816 9854 9838 983c 985c 9800 9804 98b0 98b2 98b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Atheros(R) L2 Ethernet Driver - version 2.2.3
Copyright (c) 2007 Atheros Corporation.
atl2 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
atl2 0000:06:00.0: setting latency timer to 64
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 372k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (29 C)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfebff800
b43-pci-bridge 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32.2 ehci_hcd
usb usb1: SerialNumber: 0000:00:13.5
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
b43-pci-bridge 0000:02:00.0: setting latency timer to 64
libata version 3.00 loaded.
ahci 0000:00:12.0: version 3.0
ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio slum part ccc
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffd00 irq 22
ata2: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffd80 irq 22
ata3: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffe00 irq 22
ata4: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffe80 irq 22
ssb: Sonics Silicon Backplane found on PCI device 0000:02:00.0
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfebfe000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32.2 ohci_hcd
usb usb2: SerialNumber: 0000:00:13.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pata_atiixp 0000:00:14.1: setting latency timer to 64
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfebfd000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32.2 ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfebfc000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.32.2 ohci_hcd
usb usb4: SerialNumber: 0000:00:13.2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfebfb000
usb 1-4: new high speed USB device using ehci_hcd and address 2
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.32.2 ohci_hcd
usb usb5: SerialNumber: 0000:00:13.3
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfebfa000
ata5.00: ATAPI: PIONEER DVD-RW DVRKD08, 1.00, max UDMA/33
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata5.00: configured for UDMA/33
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.32.2 ohci_hcd
usb usb6: SerialNumber: 0000:00:13.4
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 1-4: New USB device found, idVendor=0bda, idProduct=0116
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: USB2.0-CRW
usb 1-4: Manufacturer: Generic
usb 1-4: SerialNumber: 20021111153705700
usb 1-4: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
ata1: softreset failed (device not ready)
ata1: applying SB600 PMP SRST workaround and retrying
usb 1-7: new high speed USB device using ehci_hcd and address 3
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST9120822AS, 3.ALC, max UDMA/133
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST9120822AS 3.AL PQ: 0 ANSI: 5
scsi 4:0:0:0: CD-ROM PIONEER DVD-RW DVRKD08 1.00 PQ: 0 ANSI: 5
usb 1-7: New USB device found, idVendor=0c45, idProduct=624f
usb 1-7: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-7: Product: USB20 Camera
usb 1-7: configuration #1 chosen from 1 choice
sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 < sda5sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 4:0:0:0: Attached scsi generic sg1 type 5
usb 5-2: new low speed USB device using ohci_hcd and address 2
usb 5-2: New USB device found, idVendor=093a, idProduct=2500
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-2: Product: USB OPTICAL MOUSE
usb 5-2: Manufacturer: PIXART
usb 5-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:13.3/usb5/5-2/5-2:1.0/input/input2
generic-usb 0003:093A:2500.0001: input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:13.3-2/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email][email protected][/email]
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting. Commit interval 5 seconds
udev: starting version 149
ACPI: AC Adapter [AC0] (on-line)
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
ACPI: Power Button [PWRF]
ACPI: duty_cycle spans bit 4
Marking TSC unstable due to TSC halts in idle
processor LNXCPU:00: registered as cooling_device0
Asus Laptop ACPI Extras version 0.30
unsupported model F5R, trying default values
send /proc/acpi/dsdt to the developers
Switching to clocksource acpi_pm
ACPI: Battery Slot [BAT0] (battery present)
input: PC Speaker as /devices/platform/pcspkr/input/input7
ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SMB0 [0xb00-0xb0f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
acpi device:02: registered as cooling_device1
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:00/LNXVIDEO:00/input/input8
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
Driver 'rtc_cmos' needs updating - please use bus_type methods
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input9
b43-phy0: Broadcom 4311 WLAN found (core revision 10)
b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 8
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PML, Firmware-ID: FW13 ]
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
usb-storage: device scan complete
scsi 6:0:0:0: Direct-Access Generic- xD/SDMMC/MS/Pro 1.00 PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: Attached scsi generic sg2 type 0
sd 6:0:0:0: [sdb] Attached SCSI removable disk
hda_codec: ALC660-VD: BIOS auto-probing.
EXT3 FS on sda5, internal journal
fuse init (API version 7.13)
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
NTFS driver 2.1.29 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device sda2): load_system_files(): Unsupported volume flags 0x4000 encountered.
NTFS-fs warning (device sda2): load_system_files(): Volume has unsupported flags set. Will not be able to remount read-write. Run chkdsk and mount in Windows.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
atl2 0000:06:00.0: irq 28 for MSI/MSI-X
atl2: eth0 NIC Link is Up<100 Mbps Full Duplex>
NET: Registered protocol family 17
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
b43 ssb0:0: firmware: requesting b43/ucode5.fw
b43 ssb0:0: firmware: requesting b43/pcm5.fw
b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy0 debug: Chip initialized
b43-phy0 debug: 32-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Adding Interface type 2
ADDRCONF(NETDEV_UP): wlan0: link is not ready
b43-phy0: Radio hardware status changed to DISABLED
b43-phy0 debug: Removing Interface type 2
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
eth0: no IPv6 routers present
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
pci 0000:01:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to userspace modesetting.
[drm] Initialized radeon 1.31.0 20080528 for 0000:01:05.0 on minor 0
input: ACPI Virtual Keyboard Device as /devices/virtual/input/input10
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
platform radeon_cp.0: firmware: requesting radeon/R300_cp.bin
[drm] Num pipes: 2
[drm] writeback test succeeded in 1 usecs