Dysk zewn

Aristarh · Post autor: **Aristarh** » 30 października 2011, 12:38

Witam.
Mój kolega korzystał z powodzeniem z dysku ,,Elements'', zewnętrznego pod Ubuntu 10.04, wróciliśmy na święto do domu i podłączył go do komputera z Windows XP, Windows XP najpierw szukał sterowników, później wykrył dysk jako:

Kod: Zaznacz cały

Unkown  Device

czyli go nie wykrył. Po ponownym[/m podłączeniu do Ubuntu dysk się nie montuje, po próbie podłączenia do Windows Vista i Windows7 (wcześniej działał bez przeszkód) to samo co na Windows XP:

Kod: Zaznacz cały

Unkown Device

i niepowodzenie w instalowaniu sterowników. Proszę o pomoc.

Kod: Zaznacz cały

savpether@STC-Piotr:~$ uname -a
Linux STC-Piotr 2.6.32-34-generic #77-Ubuntu SMP Tue Sep 13 19:39:17 UTC 2011 x86_64 GNU/Linux

Kod: Zaznacz cały

savpether@STC-Piotr:~$ dpkg --print-architecture
amd64

Kod: Zaznacz cały

savpether@STC-Piotr:~$ lspci -k
00:00.0 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
    Kernel driver in use: agpgart-via
    Kernel modules: via-agp
00:00.1 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.5 PIC: VIA Technologies, Inc. P4M890 I/O APIC Interrupt Controller
00:00.6 Host bridge: VIA Technologies, Inc. P4M890 Security Device
00:00.7 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237/VX700 PCI Bridge
    Kernel modules: shpchp
00:02.0 PCI bridge: VIA Technologies, Inc. P4M890 PCI to PCI Bridge Controller
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
    Kernel driver in use: 8139too
    Kernel modules: 8139too, 8139cp
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
    Kernel driver in use: sata_via
    Kernel modules: sata_via
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
    Kernel driver in use: pata_via
    Kernel modules: pata_via
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
    Kernel driver in use: uhci_hcd
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
    Kernel driver in use: uhci_hcd
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
    Kernel driver in use: uhci_hcd
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
    Kernel driver in use: uhci_hcd
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
    Kernel driver in use: ehci_hcd
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
    Kernel modules: i2c-viapro
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
    Kernel driver in use: VIA 82xx Audio
    Kernel modules: snd-via82xx
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
    Kernel modules: snd-via82xx-modem
02:00.0 VGA compatible controller: nVidia Corporation NV44 [GeForce 7100 GS] (rev a1)
    Kernel driver in use: nvidia
    Kernel modules: nvidia-current, nvidiafb, nouveau

Kod: Zaznacz cały

savpether@STC-Piotr:~$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:00.5 PIC: VIA Technologies, Inc. P4M890 I/O APIC Interrupt Controller
00:00.6 Host bridge: VIA Technologies, Inc. P4M890 Security Device
00:00.7 Host bridge: VIA Technologies, Inc. P4M890 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237/VX700 PCI Bridge
00:02.0 PCI bridge: VIA Technologies, Inc. P4M890 PCI to PCI Bridge Controller
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
02:00.0 VGA compatible controller: nVidia Corporation NV44 [GeForce 7100 GS] (rev a1)

Kod: Zaznacz cały

savpether@STC-Piotr:~$ lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 054c:01bd Sony Corp. MRW62E Multi-Card Reader/Writer
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Przed podłączeniem:

Kod: Zaznacz cały

savpether@STC-Piotr:~$ dmesg | tail -n100
[    8.803230] type=1505 audit(1319966531.809:8):  operation="profile_load" pid=762 name="/usr/share/gdm/guest-session/Xsession"
[    8.815553] type=1505 audit(1319966531.819:9):  operation="profile_load" pid=766 name="/usr/lib/cups/backend/cups-pdf"
[    8.817112] type=1505 audit(1319966531.819:10):  operation="profile_load" pid=764 name="/usr/bin/evince"
[    8.822316] type=1505 audit(1319966531.829:11):  operation="profile_load" pid=766 name="/usr/sbin/cupsd"
[    9.377398]   alloc irq_desc for 24 on node -1
[    9.377402]   alloc kstat_irqs on node -1
[    9.377411] nvidia 0000:02:00.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
[    9.377421] nvidia 0000:02:00.0: setting latency timer to 64
[    9.377427] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none :o wns=io+mem
[    9.378185] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  285.05.09  Fri Sep 23 17:31:57 PDT 2011
[    9.378695] parport_pc 00:0a: reported by Plug and Play ACPI
[    9.378796] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[    9.460234] lp0: using parport0 (interrupt-driven).
[    9.502642] VIA 82xx Modem 0000:00:11.6: enabling device (0000 -> 0001)
[    9.502869] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[    9.502875]   alloc irq_desc for 22 on node -1
[    9.502877]   alloc kstat_irqs on node -1
[    9.502886] VIA 82xx Modem 0000:00:11.6: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[    9.563222] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[    9.571554] ppdev: user-space parallel port driver
[    9.637798] Console: switching to colour frame buffer device 80x30
[   10.061291] CPU0 attaching NULL sched-domain.
[   10.061298] CPU1 attaching NULL sched-domain.
[   10.121362] CPU0 attaching sched-domain:
[   10.121366]  domain 0: span 0-1 level MC
[   10.121370]   groups: 0 1
[   10.121376] CPU1 attaching sched-domain:
[   10.121379]  domain 0: span 0-1 level MC
[   10.121382]   groups: 1 0
[   10.250101] VIA 82xx Modem 0000:00:11.6: setting latency timer to 64
[   10.760274] VIA 82xx Modem 0000:00:11.6: PCI INT C disabled
[   10.760293] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
[   10.760352] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[   10.760524] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[   15.096904] CPU0 attaching NULL sched-domain.
[   15.096911] CPU1 attaching NULL sched-domain.
[   15.151354] CPU0 attaching sched-domain:
[   15.151359]  domain 0: span 0-1 level MC
[   15.151362]   groups: 0 1
[   15.151369] CPU1 attaching sched-domain:
[   15.151371]  domain 0: span 0-1 level MC
[   15.151374]   groups: 1 0
[   19.970244] eth0: no IPv6 routers present
[  283.011333] ata3: lost interrupt (Status 0x50)
[  313.040054] ata3: lost interrupt (Status 0x51)
[  318.040085] ata3.00: qc timeout (cmd 0xa0)
[  318.040098] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  318.040104] sr 2:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[  318.040118] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[  318.040119]          res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x5 (timeout)
[  318.040123] ata3.00: status: { DRDY ERR }
[  318.040148] ata3: soft resetting link
[  318.260291] ata3.00: configured for UDMA/33
[  323.261322] ata3.00: qc timeout (cmd 0xa0)
[  323.261331] ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
[  323.261356] ata3: soft resetting link
[  323.480292] ata3.00: configured for UDMA/33
[  328.481345] ata3.00: qc timeout (cmd 0xa0)
[  328.481354] ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
[  328.481360] ata3.00: limiting speed to UDMA/33:PIO3
[  328.481388] ata3: soft resetting link
[  328.700689] ata3.00: configured for UDMA/33
[  333.700108] ata3.00: qc timeout (cmd 0xa0)
[  333.700117] ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
[  333.700120] ata3.00: disabled
[  333.700160] ata3: soft resetting link
[  333.860110] ata3: EH complete
[ 4924.141476] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 4924.271555] usb 4-2: device descriptor read/64, error -71
[ 4924.511356] usb 4-2: device descriptor read/64, error -71
[ 4924.741320] usb 4-2: new full speed USB device using uhci_hcd and address 3
[ 4924.870081] usb 4-2: device descriptor read/64, error -71
[ 4925.110065] usb 4-2: device descriptor read/64, error -71
[ 4925.340061] usb 4-2: new full speed USB device using uhci_hcd and address 4
[ 4925.760038] usb 4-2: device not accepting address 4, error -71
[ 4925.880049] usb 4-2: new full speed USB device using uhci_hcd and address 5
[ 4926.310169] usb 4-2: device not accepting address 5, error -71
[ 4926.310201] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 8038.760049] usb 4-2: new full speed USB device using uhci_hcd and address 6
[ 8038.890051] usb 4-2: device descriptor read/64, error -71
[ 8039.130087] usb 4-2: device descriptor read/64, error -71
[ 8039.360039] usb 4-2: new full speed USB device using uhci_hcd and address 7
[ 8039.490054] usb 4-2: device descriptor read/64, error -71
[ 8039.730105] usb 4-2: device descriptor read/64, error -71
[ 8039.960050] usb 4-2: new full speed USB device using uhci_hcd and address 8
[ 8040.381330] usb 4-2: device not accepting address 8, error -71
[ 8040.501433] usb 4-2: new full speed USB device using uhci_hcd and address 9
[ 8040.920039] usb 4-2: device not accepting address 9, error -71
[ 8040.920061] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 8116.980053] usb 4-2: new full speed USB device using uhci_hcd and address 10
[ 8117.110086] usb 4-2: device descriptor read/64, error -71
[ 8117.350352] usb 4-2: device descriptor read/64, error -71
[ 8117.582405] usb 4-2: new full speed USB device using uhci_hcd and address 11
[ 8117.710069] usb 4-2: device descriptor read/64, error -71
[ 8117.950048] usb 4-2: device descriptor read/64, error -71
[ 8118.181366] usb 4-2: new full speed USB device using uhci_hcd and address 12
[ 8118.600020] usb 4-2: device not accepting address 12, error -71
[ 8118.720041] usb 4-2: new full speed USB device using uhci_hcd and address 13
[ 8119.140082] usb 4-2: device not accepting address 13, error -71
[ 8119.140102] hub 4-0:1.0: unable to enumerate USB device on port 2

Po podłączeniu:

Kod: Zaznacz cały

savpether@STC-Piotr:~$ dmesg | tail -n100
[    9.378796] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[    9.460234] lp0: using parport0 (interrupt-driven).
[    9.502642] VIA 82xx Modem 0000:00:11.6: enabling device (0000 -> 0001)
[    9.502869] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[    9.502875]   alloc irq_desc for 22 on node -1
[    9.502877]   alloc kstat_irqs on node -1
[    9.502886] VIA 82xx Modem 0000:00:11.6: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[    9.563222] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[    9.571554] ppdev: user-space parallel port driver
[    9.637798] Console: switching to colour frame buffer device 80x30
[   10.061291] CPU0 attaching NULL sched-domain.
[   10.061298] CPU1 attaching NULL sched-domain.
[   10.121362] CPU0 attaching sched-domain:
[   10.121366]  domain 0: span 0-1 level MC
[   10.121370]   groups: 0 1
[   10.121376] CPU1 attaching sched-domain:
[   10.121379]  domain 0: span 0-1 level MC
[   10.121382]   groups: 1 0
[   10.250101] VIA 82xx Modem 0000:00:11.6: setting latency timer to 64
[   10.760274] VIA 82xx Modem 0000:00:11.6: PCI INT C disabled
[   10.760293] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
[   10.760352] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[   10.760524] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[   15.096904] CPU0 attaching NULL sched-domain.
[   15.096911] CPU1 attaching NULL sched-domain.
[   15.151354] CPU0 attaching sched-domain:
[   15.151359]  domain 0: span 0-1 level MC
[   15.151362]   groups: 0 1
[   15.151369] CPU1 attaching sched-domain:
[   15.151371]  domain 0: span 0-1 level MC
[   15.151374]   groups: 1 0
[   19.970244] eth0: no IPv6 routers present
[  283.011333] ata3: lost interrupt (Status 0x50)
[  313.040054] ata3: lost interrupt (Status 0x51)
[  318.040085] ata3.00: qc timeout (cmd 0xa0)
[  318.040098] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  318.040104] sr 2:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[  318.040118] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[  318.040119]          res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x5 (timeout)
[  318.040123] ata3.00: status: { DRDY ERR }
[  318.040148] ata3: soft resetting link
[  318.260291] ata3.00: configured for UDMA/33
[  323.261322] ata3.00: qc timeout (cmd 0xa0)
[  323.261331] ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
[  323.261356] ata3: soft resetting link
[  323.480292] ata3.00: configured for UDMA/33
[  328.481345] ata3.00: qc timeout (cmd 0xa0)
[  328.481354] ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
[  328.481360] ata3.00: limiting speed to UDMA/33:PIO3
[  328.481388] ata3: soft resetting link
[  328.700689] ata3.00: configured for UDMA/33
[  333.700108] ata3.00: qc timeout (cmd 0xa0)
[  333.700117] ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
[  333.700120] ata3.00: disabled
[  333.700160] ata3: soft resetting link
[  333.860110] ata3: EH complete
[ 4924.141476] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 4924.271555] usb 4-2: device descriptor read/64, error -71
[ 4924.511356] usb 4-2: device descriptor read/64, error -71
[ 4924.741320] usb 4-2: new full speed USB device using uhci_hcd and address 3
[ 4924.870081] usb 4-2: device descriptor read/64, error -71
[ 4925.110065] usb 4-2: device descriptor read/64, error -71
[ 4925.340061] usb 4-2: new full speed USB device using uhci_hcd and address 4
[ 4925.760038] usb 4-2: device not accepting address 4, error -71
[ 4925.880049] usb 4-2: new full speed USB device using uhci_hcd and address 5
[ 4926.310169] usb 4-2: device not accepting address 5, error -71
[ 4926.310201] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 8038.760049] usb 4-2: new full speed USB device using uhci_hcd and address 6
[ 8038.890051] usb 4-2: device descriptor read/64, error -71
[ 8039.130087] usb 4-2: device descriptor read/64, error -71
[ 8039.360039] usb 4-2: new full speed USB device using uhci_hcd and address 7
[ 8039.490054] usb 4-2: device descriptor read/64, error -71
[ 8039.730105] usb 4-2: device descriptor read/64, error -71
[ 8039.960050] usb 4-2: new full speed USB device using uhci_hcd and address 8
[ 8040.381330] usb 4-2: device not accepting address 8, error -71
[ 8040.501433] usb 4-2: new full speed USB device using uhci_hcd and address 9
[ 8040.920039] usb 4-2: device not accepting address 9, error -71
[ 8040.920061] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 8116.980053] usb 4-2: new full speed USB device using uhci_hcd and address 10
[ 8117.110086] usb 4-2: device descriptor read/64, error -71
[ 8117.350352] usb 4-2: device descriptor read/64, error -71
[ 8117.582405] usb 4-2: new full speed USB device using uhci_hcd and address 11
[ 8117.710069] usb 4-2: device descriptor read/64, error -71
[ 8117.950048] usb 4-2: device descriptor read/64, error -71
[ 8118.181366] usb 4-2: new full speed USB device using uhci_hcd and address 12
[ 8118.600020] usb 4-2: device not accepting address 12, error -71
[ 8118.720041] usb 4-2: new full speed USB device using uhci_hcd and address 13
[ 8119.140082] usb 4-2: device not accepting address 13, error -71
[ 8119.140102] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 8417.710086] usb 4-2: new full speed USB device using uhci_hcd and address 14
[ 8417.840045] usb 4-2: device descriptor read/64, error -71
[ 8418.080043] usb 4-2: device descriptor read/64, error -71
[ 8418.311287] usb 4-2: new full speed USB device using uhci_hcd and address 15
[ 8418.440045] usb 4-2: device descriptor read/64, error -71
[ 8418.692813] usb 4-2: device descriptor read/64, error -71
[ 8418.920110] usb 4-2: new full speed USB device using uhci_hcd and address 16
[ 8419.340038] usb 4-2: device not accepting address 16, error -71
[ 8419.460043] usb 4-2: new full speed USB device using uhci_hcd and address 17
[ 8419.880037] usb 4-2: device not accepting address 17, error -71
[ 8419.880060] hub 4-0:1.0: unable to enumerate USB device on port 2

I na koniec:

Kod: Zaznacz cały

savpether@STC-Piotr:~$ sudo fdisk -l
[sudo] password for savpether: 

Dysk /dev/sda: 250.1 GB, bajtów: 250059350016
głowic: 255, sektorów/ścieżkę: 63, cylindrów: 30401
Jednostka = cylindrów, czyli 16065 * 512 = 8225280 bajtów
Rozmiar sektora (logiczny/fizyczny) w bajtach: 512 / 512
Rozmiar we/wy (minimalny/optymalny) w bajtach: 512 / 512
Identyfikator dysku: 0x36c31b6e

Urządzenie Rozruch   Początek      Koniec   Bloków   ID  System
/dev/sda1   *           1       23455   188400640   83  Linux
/dev/sda3           23455       30402    55796736    7  HPFS/NTFS

Pozdrawiam,
Piotr

Post autor: **Yampress** » 30 października 2011, 16:58

Zobacz, czy widoczne są partycje na tym dysku:

Kod: Zaznacz cały

fdisk -l   /dev/nazwa_dysku

Jako root.

Aristarh · Post autor: **Aristarh** » 31 października 2011, 12:44

Problem w tym, że nie wiem jak dysk jest oznaczony w /dev. Jakbym wiedział to bym go próbował ręcznie zamontować.

Post autor: **Yampress** » 31 października 2011, 12:50

Zajrzyj do katalogu /dev, jakie urządzenia są przed wsadzeniem dysku, głównie te /dev/sd*. Podłącz dysk zobacz jakie przybyły lub popatrz w logi /var/log/dmesg, zaraz po podłączeniu.

Kod: Zaznacz cały

su -c " tail -20  /var/log/dmesg"

Aristarh · Post autor: **Aristarh** » 31 października 2011, 13:14

Ani przy podanym poleceniu, ani w dev nie ma żadnych różnic przed i po podłączeniu dysku..

fnmirk · Post autor: **fnmirk** » 31 października 2011, 13:22

Przecież podał te logi i z nich wynika, że ma problem z obsługą usb. Odepnij ten czytnik pamięci, czy co tam masz podłączone i sprawdź ponownie.
A najlepiej to pobierz sobie Knoppiksa i sprawdź, czy masz wszystko sprawne. System sprzęt itp.
http://debian.linux.pl/threads/9479-Dys ... #post61503

Post autor: **Yampress** » 31 października 2011, 13:23

Czyżby się popsuł? Po podłączeniu posłuchaj czy działa. Spróbuj innego gniazda usb, spróbuj na krótszym kablu jeśli masz przedłużacz.

Aristarh · Post autor: **Aristarh** » 31 października 2011, 14:45

Sprzęt mam sprawny, sprawdzałem dysk na 7 komputerach z: Ubuntu 10.04, Kubuntu 11.10, Windows7, Windows Vista, Windows XP, Archlinux, Debian stabilny. Wszędzie to samo. Chodzi, po podłączeniu czuje, że wibruje i słyszę jak się obraca, kontrolka się pali.

Zrzut ekranu z Menedżera urządzeń:

Kod: Zaznacz cały

http://www.imghost.pl/images/2ce30dda14.png

Dodane:
Po podłączeniu dysku i

Kod: Zaznacz cały

tail /log/var/messages

dostaję:

Kod: Zaznacz cały

savpether@LAP-Piotr:~$ tail /var/log/messages 
Oct 31 10:18:30 LAP-Piotr kernel: [   31.552184] cfg80211: Current regulatory domain updated by AP to: SA
Oct 31 10:18:30 LAP-Piotr kernel: [   31.552186]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Oct 31 10:18:30 LAP-Piotr kernel: [   31.552189]     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Oct 31 10:43:21 LAP-Piotr pulseaudio[1913]: ratelimit.c: 2 events suppressed
Oct 31 12:18:46 LAP-Piotr bonobo-activation-server (savpether-2810): could not associate with desktop session: Failed to connect to socket /tmp/dbus-O3rDM8wES3: Połączenie odrzucone
Oct 31 12:18:52 LAP-Piotr pulseaudio[2949]: pid.c: Stale PID file, overwriting.
Oct 31 14:41:58 LAP-Piotr kernel: [15839.571341] usb 4-1: new full speed USB device using uhci_hcd and address 3
Oct 31 14:41:59 LAP-Piotr kernel: [15840.170101] usb 4-1: new full speed USB device using uhci_hcd and address 4
Oct 31 14:41:59 LAP-Piotr kernel: [15840.772368] usb 4-1: new full speed USB device using uhci_hcd and address 5
Oct 31 14:42:00 LAP-Piotr kernel: [15841.310099] usb 4-1: new full speed USB device using uhci_hcd and address 6
savpether@LAP-Piotr:~$ tail /var/log/messages 
Oct 31 12:18:46 LAP-Piotr bonobo-activation-server (savpether-2810): could not associate with desktop session: Failed to connect to socket /tmp/dbus-O3rDM8wES3: Połączenie odrzucone
Oct 31 12:18:52 LAP-Piotr pulseaudio[2949]: pid.c: Stale PID file, overwriting.
Oct 31 14:41:58 LAP-Piotr kernel: [15839.571341] usb 4-1: new full speed USB device using uhci_hcd and address 3
Oct 31 14:41:59 LAP-Piotr kernel: [15840.170101] usb 4-1: new full speed USB device using uhci_hcd and address 4
Oct 31 14:41:59 LAP-Piotr kernel: [15840.772368] usb 4-1: new full speed USB device using uhci_hcd and address 5
Oct 31 14:42:00 LAP-Piotr kernel: [15841.310099] usb 4-1: new full speed USB device using uhci_hcd and address 6
Oct 31 14:43:14 LAP-Piotr kernel: [15915.070104] usb 4-1: new full speed USB device using uhci_hcd and address 7
Oct 31 14:43:14 LAP-Piotr kernel: [15915.670112] usb 4-1: new full speed USB device using uhci_hcd and address 8
Oct 31 14:43:15 LAP-Piotr kernel: [15916.270112] usb 4-1: new full speed USB device using uhci_hcd and address 9
Oct 31 14:43:15 LAP-Piotr kernel: [15916.810068] usb 4-1: new full speed USB device using uhci_hcd and address 10

Czyli jednak widzi "urządzenie USB"

fnmirk · Post autor: **fnmirk** » 31 października 2011, 14:46

Według informacji dostępnych w internecie, dysk wymaga instalacji sterowników i prawdopodobnie (moim zdaniem) lepszego zasilania. Należy odpiąć wszystko co jest podpięte do portów usb, poszukać sterowników w przypadku Windows, a w przypadku Linuksa - Knoppix powinien to zobaczyć.

Aristarh · Post autor: **Aristarh** » 31 października 2011, 14:50

Przypomnę jednak, że przed podłączeniem do windowsa xp, dysk działał sprawnie na wszystkich urządzeniach bez instalacji dodatkowych sterowników i dodatkowego zasilania(działał bez żadnej ingerencji, był podłączany, wykrywany i po prostu działał), dlatego też instalacja sterowników, czy dodatkowe zasilanie nie jest rozwiązaniem tego problemu.

Dysk zewn

Dysk zewnętrzny USB popsuty przez Windows XP