B

[markossx]

Na podstawie tych informacji nie da rady ustalić jaki to konkretnie kontroler. Użyj lspci lub jak nie masz to zainstaluj paczkę pciutils.

[mardom]

Kod: Zaznacz cały

root@TYTAN:/# lspci
00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11)
00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11)
00:05.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 3 (rev 11)
00:08.0 System peripheral: Intel Corporation Core Processor System Management Registers (rev 11)
00:08.1 System peripheral: Intel Corporation Core Processor Semaphore and Scratchpad Registers (rev 11)
00:08.2 System peripheral: Intel Corporation Core Processor System Control and Status Registers (rev 11)
00:08.3 System peripheral: Intel Corporation Core Processor Miscellaneous Registers (rev 11)
00:10.0 System peripheral: Intel Corporation Core Processor QPI Link (rev 11)
00:10.1 System peripheral: Intel Corporation Core Processor QPI Routing and Protocol Registers (rev 11)
00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05)
00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 05)
00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation 3400 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA IDE Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.5 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 2 port SATA IDE Controller (rev 05)
01:00.0 RAID bus controller: LSI Logic / Symbios Logic LSI MegaSAS 9260 (rev 04)
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
06:03.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200eW WPCM450 (rev 0a)

[markossx]

Kontroler masz LSI MegaSAS 9260, teraz:

Kod: Zaznacz cały

man smartctl

i poszukaj frazy ,,megaraid''.

[mardom]

Kod: Zaznacz cały

root@TYTAN:~# smartctl -a -d megaraid,2 /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, [url]http://smartmontools.sourceforge.net[/url]

/dev/sda [megaraid_disk_02] [SAT]: Device open changed type from 'megaraid' to 'sat'
=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1003FBYX-01Y7B0
Serial Number:    WD-WCAW30218016
Firmware Version: 01.01V01
User Capacity:    1,000,204,886,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Thu Aug 29 11:38:41 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (16860) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 174) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       1
  3 Spin_Up_Time            0x0027   173   172   021    Pre-fail  Always       -       4316
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       97
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   076   076   000    Old_age   Always       -       17862
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       94
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       93
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       3
194 Temperature_Celsius     0x0022   119   101   000    Old_age   Always       -       28
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@TYTAN:~#

Kod: Zaznacz cały

root@TYTAN:~# smartctl -a -d megaraid,0 /dev/sdb
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, [url]http://smartmontools.sourceforge.net[/url]

/dev/sdb [megaraid_disk_00] [SAT]: Device open changed type from 'megaraid' to 'sat'
=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1003FBYX-01Y7B0
Serial Number:    WD-WCAW30383524
Firmware Version: 01.01V01
User Capacity:    1,000,204,886,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Thu Aug 29 11:40:07 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (16680) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 172) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   174   171   021    Pre-fail  Always       -       4283
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       105
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   073   073   000    Old_age   Always       -       20253
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       104
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       103
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       1
194 Temperature_Celsius     0x0022   120   101   000    Old_age   Always       -       27
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@TYTAN:~#

[markossx]

Mówiłeś, że są cztery dyski a listing jest z dwóch.Poproszę o dwa kolejne i wynik lsmod.

[mardom]

Kod: Zaznacz cały

root@TYTAN:~# lsmod
Module                  Size  Used by
nfsd                  254142  11
lockd                  57331  1 nfsd
nfs_acl                 2031  1 nfsd
auth_rpcgss            33476  1 nfsd
sunrpc                160556  10 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs                3138  1 nfsd
loop                   11639  0
sg                     23909  0
snd_pcm                60151  0
snd_timer              15502  1 snd_pcm
snd                    46014  2 snd_pcm,snd_timer
sr_mod                 12250  0
cdrom                  28567  1 sr_mod
soundcore               4566  1 snd
i2c_i801                7750  0
ehci_hcd               32145  0
ata_generic             3239  0
snd_page_alloc          6233  1 snd_pcm
ata_piix               21140  0
i2c_core               15451  1 i2c_i801
psmouse                49969  0
usbcore               123127  2 ehci_hcd
evdev                   7352  3
serio_raw               3752  0
pcspkr                  1699  0
libata                133312  2 ata_generic,ata_piix
e1000e                124740  0
nls_base                6377  1 usbcore
button                  4650  0
processor              29887  4
ext4                  288446  4
mbcache                 5050  1 ext4
jbd2                   67079  1 ext4
crc16                   1319  1 ext4
shpchp                 26216  0
pci_hotplug            21587  1 shpchp
sd_mod                 29713  7
crc_t10dif              1276  1 sd_mod
megaraid_sas           58687  5
scsi_mod              126437  5 sg,sr_mod,libata,sd_mod,megaraid_sas
thermal                11610  0
thermal_sys            11942  2 processor,thermal
root@TYTAN:~#

Są 4 dyski ale w macierzy. Dwa są lustrami tych dwóch.

[markossx]

Nam zależy, żeby poznać sprawność wszystkich fizycznych dysków.Te dwa wyglądają na ok, wylistuj dwa pozostałe.

[mardom]

Nie wiem jak to zrobić, wcześniej skorzystałem z podręcznika systemowego:

Kod: Zaznacz cały

Under Linux , to look at SCSI/SAS disks behind LSI MegaRAID controllers, use syntax such as:
              smartctl -a -d megaraid,2 /dev/sda
              smartctl -a -d megaraid,0 /dev/sdb
              where in the argument megaraid,N, the integer N is the physical disk number within  the  MegaRAID  con‐
              troller.   This  interface will also work for Dell PERC controllers.  The following /dev/XXX entry must
              exist:
              For PERC2/3/4 controllers: /dev/megadev0
              For PERC5/6 controllers: /dev/megaraid_sas_ioctl_node

A jak wejdę /dev to mam:

Kod: Zaznacz cały

sda
sda1
sda2
sda5
sda6
sdb
sdb1
sdb2

Ale to są partycje.

Kod: Zaznacz cały

root@TYTAN:/dev# smartctl -a -d megaraid,0 /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, [url]http://smartmontools.sourceforge.net[/url]

/dev/sda [megaraid_disk_00] [SAT]: Device open changed type from 'megaraid' to 'sat'
=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1003FBYX-01Y7B0
Serial Number:    WD-WCAW30383524
Firmware Version: 01.01V01
User Capacity:    1,000,204,886,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Thu Aug 29 13:36:20 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (16680) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 172) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   174   171   021    Pre-fail  Always       -       4283
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       105
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   073   073   000    Old_age   Always       -       20255
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       104
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       103
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       1
194 Temperature_Celsius     0x0022   120   101   000    Old_age   Always       -       27
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@TYTAN:/dev#

[markossx]

Rzecz jest w tym, że masz myśleć a nie przepisywać "na pałę". Dowiedz się, jak wylistować wszystkie fizyczne dyski i daj znać.

[mardom]

Mam pytanie, czy z poziomu Debiana jest możliwość sprawdzenia tego?

Bo tak "sda" to jest dysk pierwszy "sdb" to jest dysk drugi. Jak używam polecenia to co oznacza zero za słowem "megaraid,0" - partycje?

Kod: Zaznacz cały

smartctl -a -d megaraid,0 /dev/sda