Które j

Ogólne pytania dotyczące systemu
rox11
Posty: 48
Rejestracja: 10 kwietnia 2007, 06:57

Post autor: rox11 »

a więc tak po instalacji sieć nie chodzi, a tu wyniki:

192.168.100.252 to mój router jest. ping do niego nie chodzi.

na live cd karta chodzi, ale nie na każdym. Może hotplug powinien być, sam nie wiem.

Kod: Zaznacz cały

eth0      Link encap:Ethernet  HWaddr 00:e0:29:0d:10:e9  
          inet addr:192.168.100.7  Bcast:192.168.100.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11 Base address:0x8f80 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:24 errors:0 dropped:0 overruns:0 frame:0
          TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1568 (1.5 KiB)  TX bytes:1568 (1.5 KiB)

Kod: Zaznacz cały

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.100.0   0.0.0.0         255.255.255.0   U     0      0        0 eth0
0.0.0.0         192.168.100.252 0.0.0.0         UG    0      0        0 eth0

Kod: Zaznacz cały

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

auto eth0
iface eth0 inet static
address 192.168.100.7
netmask 255.255.255.0
gateway 192.168.100.252

Kod: Zaznacz cały

00:05.0 Host bridge: Hint Corp VXPro II Chipset
	Subsystem: Hint Corp VXPro II Chipset CPU to PCI Bridge
	Flags: bus master, 66MHz, slow devsel, latency 64

00:05.1 ISA bridge: Hint Corp VXPro II Chipset
	Subsystem: Hint Corp VXPro II Chipset PCI to ISA Bridge
	Flags: bus master, 66MHz, slow devsel, latency 64

00:05.2 IDE interface: Hint Corp VXPro II IDE (prog-if 00 [])
	Subsystem: Hint Corp VXPro II Chipset EIDE Controller
	Flags: medium devsel
	[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=200]
	[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=75]
	[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=200]
	[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=75]
	Kernel modules: ide-pci-generic, ata_generic

00:09.0 Ethernet controller: Digital Equipment Corporation DECchip 21041 [Tulip Pass 3] (rev 11)
	Flags: bus master, medium devsel, latency 64, IRQ 11
	I/O ports at ec80 [size=200]
	Memory at ebfeff80 (32-bit, non-prefetchable) [size=200]
	Expansion ROM at ebf80000 [disabled] [size=256K]
	Kernel driver in use: de2104x
	Kernel modules: de2104x

00:0a.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01) (prog-if 00 [VGA controller])
	Subsystem: S3 Inc. ViRGE/DX
	Flags: bus master, medium devsel, latency 64
	Memory at ec000000 (32-bit, non-prefetchable) [size=64M]
	Expansion ROM at ebff0000 [disabled] [size=64K]
	Kernel modules: s3fb



[ Dodano: 2009-03-21, 19:36 ]
i jeszcze dodam:
dmesg

Kod: Zaznacz cały

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-1-486 (Debian 2.6.26-13) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 Sat Jan 10 17:46:23 UTC 2009
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000003000000 (usable)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
[    0.000000] 48MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 12288) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->    12288
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->    12288
[    0.000000] On node 0 totalpages: 12288
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI not present or invalid.
[    0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321]
[    0.000000] Allocating PCI resources starting at 10000000 (gap: 03000000:fbc00000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 12192
[    0.000000] Kernel command line: root=/dev/hda1 ro all_generic_ide quiet
[    0.000000] No local APIC present or hardware disabled
[    0.000000] mapped APIC to ffffb000 (01062000)
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[    0.000000] Detected 233.050 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.004000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.004000] Memory: 39104k/49152k available (1694k kernel code, 9656k reserved, 745k data, 320k init, 0k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xfffb3000 - 0xfffff000   ( 304 kB)
[    0.004000]     vmalloc : 0xc3800000 - 0xfffb1000   ( 967 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xc3000000   (  48 MB)
[    0.004000]       .init : 0xc0364000 - 0xc03b4000   ( 320 kB)
[    0.004000]       .data : 0xc02a7b13 - 0xc0362000   ( 745 kB)
[    0.004000]       .text : 0xc0100000 - 0xc02a7b13   (1694 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.085549] Calibrating delay using timer specific routine.. 467.35 BogoMIPS (lpj=934714)
[    0.086161] Security Framework initialized
[    0.086315] SELinux:  Disabled at boot.
[    0.086378] Capability LSM initialized
[    0.086543] Mount-cache hash table entries: 512
[    0.088005] Initializing cgroup subsys ns
[    0.088005] Initializing cgroup subsys cpuacct
[    0.088005] Initializing cgroup subsys devices
[    0.088313] Intel Pentium with F0 0F bug - workaround enabled.
[    0.088368] 
[    0.088673] CPU: Intel Pentium MMX stepping 03
[    0.088763] Checking 'hlt' instruction... OK.
[    0.126091] Freeing SMP alternatives: 0k freed
[    0.126136] ACPI: Core revision 20080321
[    0.126732] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321]
[    0.126791] ACPI: Unable to load the System Description Tables
[    0.132211] net_namespace: 652 bytes
[    0.132292] Booting paravirtualized kernel on bare hardware
[    0.135512] NET: Registered protocol family 16
[    0.142149] EISA bus registered
[    0.172151] PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=0
[    0.172223] Setting up standard PCI resources
[    0.197870] ACPI: Interpreter disabled.
[    0.197931] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.198725] pnp: PnP ACPI: disabled
[    0.198772] PnPBIOS: Scanning system for PnP BIOS support...
[    0.199169] PnPBIOS: Found PnP BIOS installation structure at 0xc00f8730
[    0.199215] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x808e, dseg 0xf0000
[    0.217998] PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
[    0.224997] PCI: Probing PCI hardware
[    0.225053] PCI: Probing PCI hardware (bus 00)
[    0.236148] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.236203] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[    0.236358] system 00:0d: ioport range 0x4d0-0x4d1 has been reserved
[    0.236403] system 00:0d: ioport range 0xcf8-0xcff has been reserved
[    0.236443] system 00:0d: ioport range 0x3f7-0x3f7 has been reserved
[    0.236483] system 00:0d: ioport range 0x108-0x109 has been reserved
[    0.236537] system 00:0d: iomem range 0xfffe0000-0xffffffff could not be reserved
[    0.236580] system 00:0d: iomem range 0x100000-0x2ffffff could not be reserved
[    0.246746] NET: Registered protocol family 2
[    0.247939] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.250492] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.250983] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.251246] TCP: Hash tables configured (established 2048 bind 2048)
[    0.251287] TCP reno registered
[    0.252339] NET: Registered protocol family 1
[    0.253992] checking if image is initramfs... it is
[    8.252329] Freeing initrd memory: 6035k freed
[    8.262966] audit: initializing netlink socket (disabled)
[    8.263229] type=2000 audit(1203855204.259:1): initialized
[    8.264770] Total HugeTLB memory allocated, 0
[    8.265918] VFS: Disk quotas dquot_6.5.1
[    8.266323] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    8.267091] msgmni has been set to 88
[    8.270890] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    8.270955] io scheduler noop registered
[    8.270981] io scheduler anticipatory registered
[    8.271009] io scheduler deadline registered
[    8.271147] io scheduler cfq registered (default)
[    8.271393] pci 0000:00:0a.0: Boot video device
[    8.278033] isapnp: Scanning for PnP cards...
[    8.374191]  01:01: card 'PnP Sound Chip'
[    8.374236] isapnp: 1 Plug & Play card detected total
[    8.437528] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    8.438844] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    8.440229] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    8.446183] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    8.448591] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    8.483276] brd: module loaded
[    8.485281] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[    8.485334] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    8.487442] serio: i8042 KBD port at 0x60,0x64 irq 1
[    8.490319] mice: PS/2 mouse device common for all mice
[    8.492636] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    8.492785] rtc0: alarms up to one day
[    8.495316] EISA: Probing bus 0 at eisa.0
[    8.495606] EISA: Detected 0 cards.
[    8.495656] cpuidle: using governor ladder
[    8.495689] cpuidle: using governor menu
[    8.495922] No iBFT detected.
[    8.500329] TCP cubic registered
[    8.500376] NET: Registered protocol family 17
[    8.500477] Using IPI Shortcut mode
[    8.503379] registered taskstats version 1
[    8.504331] rtc_cmos 00:04: setting system clock to 2008-02-24 12:13:25 UTC (1203855205)
[    8.513635] Freeing unused kernel memory: 320k freed
[    8.534286] input: AT Translated Set 2 keyboard as /class/input/input0
[    9.587113] Uniform Multi-Platform E-IDE driver
[    9.587200] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    9.597033] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[    9.597175] Probing IDE interface ide0...
[    9.883830] hda: ST32520A, ATA DISK drive
[   10.331806] hdb: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
[   10.388726] Probing IDE interface ide1...
[   10.952807] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   10.953347] ide1 at 0x170-0x177,0x376 on irq 15
[   11.453961] thermal: Unknown symbol acpi_processor_set_thermal_limit
[   15.434852] hda: max request size: 128KiB
[   15.434920] hda: 4927104 sectors (2522 MB), CHS=4888/16/63
[   15.434961] hda: cache flushes not supported
[   15.435452]  hda: hda1 hda2 < hda5 >
[   15.958406] HINT_IDE: IDE controller (0x3388:0x8013 rev 0x00) at  PCI slot 0000:00:05.2
[   15.958561] PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:05.2
[   15.958599] HINT_IDE: can't reserve resources
[   15.958785] PCI_IDE: probe of 0000:00:05.2 failed with error -16
[   16.089161] de2104x PCI Ethernet driver v0.7 (Mar 17, 2004)
[   16.333832] de0: SROM leaf offset 30, default media 10baseT auto
[   16.333899] de0:   media block #0: 10baseT-FD
[   16.333928] de0:   media block #1: BNC
[   16.333952] de0:   media block #2: AUI
[   16.333977] de0:   media block #3: 10baseT-HD
[   16.337028] eth0: 21041 at 0xc3838f80, 00:e0:29:0d:10:e9, IRQ 11
[   16.363554] hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
[   16.363627] Uniform CD-ROM driver Revision: 3.20
[   16.649226] SCSI subsystem initialized
[   17.115800] Floppy drive(s): fd0 is 1.44M
[   17.426733] FDC 0 is an 8272A
[   18.764169] libata version 3.00 loaded.
[   18.783004] PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:05.2
[   18.783067] ata_generic 0000:00:05.2: failed to request/iomap BARs for port 0 (errno=-16)
[   18.783120] PCI: Unable to reserve I/O region #3:8@170 for device 0000:00:05.2
[   18.783160] ata_generic 0000:00:05.2: failed to request/iomap BARs for port 1 (errno=-16)
[   18.783200] ata_generic 0000:00:05.2: no available native port
[   19.182388] PM: Starting manual resume from disk
[   19.484897] kjournald starting.  Commit interval 5 seconds
[   19.485056] EXT3-fs: mounted filesystem with ordered data mode.
[   26.031757] udevd version 125 started
[   35.212717] input: PC Speaker as /class/input/input1
[   43.963208] Error: Driver 'pcspkr' is already registered, aborting...
[   45.591297] parport_pc 00:0b: reported by Plug and Play BIOS
[   45.591483] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   45.818127] sb: Init: Starting Probe...
[   45.910931] sb: Init: Done
[   46.286541] als100 01:01.00: activated
[   46.289041] als100 01:01.03: activated
[   46.291435] als100 01:01.01: activated
[   47.753328] sb: Init: Starting Probe...
[   47.753801] sb: Init: Done
[   48.532973] ns558 01:01.02: activated
[   48.569501] gameport: NS558 PnP Gameport is pnp01:01.02/gameport0, io 0x200, speed 493kHz
[   53.358550] Adding 128480k swap on /dev/hda5.  Priority:-1 extents:1 across:128480k
[   54.339114] EXT3 FS on hda1, internal journal
[   60.055585] eth0: enabling interface
[   60.087923] eth0: set link 10baseT auto
[   60.087944] eth0:    mode 0x7ffc0040, sia 0x10c4,0xffffef01,0xffffffff,0xffff0008
[   60.087973] eth0:    set mode 0x7ffc0040, set sia 0xef01,0xffff,0x8
[   61.537476] eth0: link up, media 10baseT auto
[  539.104968] floppy0: disk absent or changed during operation
[  539.105058] end_request: I/O error, dev fd0, sector 21
[  539.105272] Buffer I/O error on device fd0, logical block 21
[  539.105417] lost page write due to I/O error on fd0
[  582.286153] VFS: busy inodes on changed media.
i
lsmod

Kod: Zaznacz cały

Module                  Size  Used by
nls_utf8                1792  1 
nls_cp437               5504  1 
vfat                    8960  1 
fat                    40220  1 vfat
nls_base                6528  4 nls_utf8,nls_cp437,vfat,fat
ns558                   3712  0 
gameport               10504  2 ns558
snd_als100              6436  0 
snd_opl3_lib            9344  1 snd_als100
snd_hwdep               6148  1 snd_opl3_lib
snd_sb16_dsp            8448  1 snd_als100
snd_sb_common          14848  2 snd_als100,snd_sb16_dsp
parport_pc             22436  0 
snd_mpu401_uart         6400  1 snd_als100
sb_lib                 38212  0 
parport                30408  1 parport_pc
uart401                 8772  1 sb_lib
snd_rawmidi            18592  1 snd_mpu401_uart
snd_seq_device          6412  2 snd_opl3_lib,snd_rawmidi
sound                  65416  2 sb_lib,uart401
sound_firmware          1792  1 sb_lib
snd_pcm                60680  2 snd_als100,snd_sb16_dsp
snd_timer              17668  2 snd_opl3_lib,snd_pcm
snd                    44964  10 snd_als100,snd_opl3_lib,snd_hwdep,snd_sb16_dsp,snd_sb_common,snd_mpu401_uart,snd_rawmidi,snd_seq_device,snd_pcm,snd_timer
soundcore               6112  2 sound,snd
snd_page_alloc          7816  1 snd_pcm
pcspkr                  2304  0 
evdev                   7808  0 
ext3                  103688  1 
jbd                    35092  1 ext3
mbcache                 6656  1 ext3
ata_generic             4612  0 
libata                141088  1 ata_generic
floppy                 47620  1 
scsi_mod              129804  1 libata
dock                    8076  1 libata
de2104x                17280  0 
ide_pci_generic         3844  0 [permanent]
ide_cd_mod             27652  0 
cdrom                  30240  1 ide_cd_mod
ide_disk               10496  3 
thermal_sys            10784  0 
ide_generic             2432  0 [permanent]
ide_core               95144  4 ide_pci_generic,ide_cd_mod,ide_disk,ide_generic
ODPOWIEDZ