Polskie Forum Użytkowników Debiana

Polski portal użytkowników dystrybucji Debian GNU/Linux, dyskusje, artykuły, nowości, blog, porady, pomoc.
https://593930.wb34atkl.asia/

System przestal sie bootowac w AHCI Mode

https://593930.wb34atkl.asia/viewtopic.php?t=33921

Strona 2 z 2

Re: System przestal sie bootowac w AHCI Mode

: 27 maja 2016, 17:29
autor: AKJ
Output jest dlugi:

Kod: Zaznacz cały

smartctl 6.4 2014-10-07 r4002 [x86_64-linux-4.0.0-kali1-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Momentus 5400.6
Device Model:     ST9500325AS
Serial Number:    5VEHJW4V
LU WWN Device Id: 5 000c50 038b8366f
Firmware Version: 0001SDM1
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Fri May 27 17:28:22 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (  73)	The previous self-test completed having
					a test element that failed and the test
					element that failed is not known.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 145) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x103b)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   086   083   006    Pre-fail  Always       -       152099973
  3 Spin_Up_Time            0x0003   098   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4634
  5 Reallocated_Sector_Ct   0x0033   005   005   036    Pre-fail  Always   FAILING_NOW 1963
  7 Seek_Error_Rate         0x000f   086   060   030    Pre-fail  Always       -       410001816
  9 Power_On_Hours          0x0032   079   079   000    Old_age   Always       -       19041
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   020    Old_age   Always       -       4492
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   001   001   000    Old_age   Always       -       1113
188 Command_Timeout         0x0032   100   088   000    Old_age   Always       -       64425492505
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   061   051   045    Old_age   Always       -       39 (Min/Max 25/39)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       122
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       16
193 Load_Cycle_Count        0x0032   026   026   000    Old_age   Always       -       149536
194 Temperature_Celsius     0x0022   039   049   000    Old_age   Always       -       39 (0 8 0 0 0)
195 Hardware_ECC_Recovered  0x001a   049   042   000    Old_age   Always       -       152099973
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       135
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       135
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
254 Free_Fall_Sensor        0x0032   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 1126 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1126 occurred at disk power-on lifetime: 19030 hours (792 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 00 00 00 00 00 a0 00      00:04:35.169  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 00      00:04:35.161  IDENTIFY DEVICE
  00 00 00 00 00 00 00 04      00:04:35.005  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      00:04:33.664  NOP [Abort queued commands]
  a1 00 00 00 00 00 a0 00      00:04:28.664  IDENTIFY PACKET DEVICE

Error 1125 occurred at disk power-on lifetime: 19030 hours (792 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 00      00:04:35.161  IDENTIFY DEVICE
  00 00 00 00 00 00 00 04      00:04:35.005  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      00:04:33.664  NOP [Abort queued commands]
  a1 00 00 00 00 00 a0 00      00:04:28.664  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 00      00:04:28.656  IDENTIFY DEVICE

Error 1124 occurred at disk power-on lifetime: 19030 hours (792 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 00 00 00 00 00 a0 00      00:04:28.664  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 00      00:04:28.656  IDENTIFY DEVICE
  00 00 00 00 00 00 00 04      00:04:28.500  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      00:04:27.160  NOP [Abort queued commands]
  a1 00 00 00 00 00 a0 00      00:04:27.120  IDENTIFY PACKET DEVICE

Error 1123 occurred at disk power-on lifetime: 19030 hours (792 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 00      00:04:28.656  IDENTIFY DEVICE
  00 00 00 00 00 00 00 04      00:04:28.500  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      00:04:27.160  NOP [Abort queued commands]
  a1 00 00 00 00 00 a0 00      00:04:27.120  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 00      00:04:27.088  IDENTIFY DEVICE

Error 1122 occurred at disk power-on lifetime: 19030 hours (792 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 00 00 00 00 00 a0 00      00:04:27.120  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 00      00:04:27.088  IDENTIFY DEVICE
  25 00 00 ff ff ff ef 00      00:04:08.748  READ DMA EXT
  25 00 e0 ff ff ff ef 00      00:04:08.747  READ DMA EXT
  25 00 10 ff ff ff ef 00      00:04:08.734  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Conveyance offline  Completed: unknown failure    90%     19041         0
# 2  Extended offline    Completed: unknown failure    90%     19041         0
# 3  Short offline       Completed: unknown failure    90%     19041         0
# 4  Conveyance offline  Completed without error       00%     18549         -
# 5  Short offline       Completed without error       00%     18549         -
# 6  Short offline       Completed without error       00%         0         -
# 7  Conveyance offline  Completed without error       00%         0         -
# 8  Short offline       Completed without error       00%         0         -
# 9  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Ale ta linijka bardzo mnie smuci, z tego co znalazlem w sieci, chyba trzeba znalezc inny dysk :(

Kod: Zaznacz cały

  5 Reallocated_Sector_Ct   0x0033   005   005   036    Pre-fail  Always   FAILING_NOW 1963

Re: System przestal sie bootowac w AHCI Mode

: 27 maja 2016, 17:39
autor: dedito
No parametr 5 wskazuje, że dysk ma uszkodzone sektory, które zostały zastąpione z puli zapasowej.
Wykonaj kopie danych i dysk do wymiany, ewentualnie na mało ważne dane z dodatkową obserwacją czy wartość nie rośnie.
Aczkolwiek nie jestem specjalistą i sugeruję jeszcze zasięgnąć porady w sprawie tego parametru 05 u fachowców (czasem zdarzają się błędy logiczne, które da się skorygować w dmde czy mhdd).

Re: System przestal sie bootowac w AHCI Mode

: 27 maja 2016, 22:39
autor: Yampress
A na dysku jest bootloader?
Może spróbował byś przywrócić/zainstalować ponownie grub
Strefa czasowa UTC+01:00
Strona 2 z 2

Technologię dostarcza phpBB® Forum Software © phpBB Limited

Polski pakiet językowy dostarcza phpBB.pl