Strona 1 z 1

Huawei E3276 nie łączy się z netem

: 23 listopada 2014, 08:13
autor: Henk100
Mam problem z modemem Huawei E3276.

Po włożeniu do usb jest wykrywany i mogę go skonfigurować. Ale kiedy chcę się połączyć, to po kilkunastu sekundach wyskakuje komunikat, że połączenie się nie powiodło.

Modem jest z sieci Plus. Na netbooku mam Debiana Gnome.

Jak można rozwiązać ten problem?

: 23 listopada 2014, 10:10
autor: marcin1982
Czasami warto skorzystać z forumowej wyszukiwarki:
threads/30730-Huawei-E3276-internet-LTE ... post168425 .

: 23 listopada 2014, 11:34
autor: Henk100
marcin1982 pisze:Czasami warto skorzystać z forumowej wyszukiwarki:
threads/30730-Huawei-E3276-internet-LTE ... post168425 .
Wiem,że warto, Marcinie. Ten sposób jednak u mnie nie zadziałał. Gdyby ktoś mógł mi podpowiedzieć jak uruchomić ten modem, to byłbym wdzięczny.

ATZ - nie znaleziono polecenia

AT^SETPORT="A1,A2;1,2,3" - nie znaleziono polecenia

lsusb
$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0ac8:c33f Z-Star Microelectronics Corp. Webcam
Bus 004 Device 002: ID 0a5c:219b Broadcom Corp. Bluetooth 2.1 Device
Bus 001 Device 005: ID 12d1:1506 Huawei Technologies Co., Ltd. E398 LTE/UMTS/GSM Modem/Networkcard
dmesg

Kod: Zaznacz cały

[    0.210007] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.210143] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.210281] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.210416] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.210658] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.210658] vgaarb: loaded
[    0.210658] vgaarb: bridge control possible 0000:00:02.0
[    0.210658] PCI: Using ACPI for IRQ routing
[    0.210658] PCI: pci_cache_line_size set to 64 bytes
[    0.210658] reserve RAM buffer: 000000000009dc00 - 000000000009ffff 
[    0.210658] reserve RAM buffer: 000000003f5b0000 - 000000003fffffff 
[    0.210658] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.210658] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.210658] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.216187] Switching to clocksource hpet
[    0.219816] pnp: PnP ACPI init
[    0.219856] ACPI: bus type pnp registered
[    0.221480] pnp 00:00: [bus 00-3f]
[    0.221488] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.221494] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.221501] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.221507] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    0.221513] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    0.221519] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    0.221525] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    0.221531] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    0.221538] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    0.221544] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    0.221550] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    0.221556] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    0.221562] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    0.221568] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    0.221575] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    0.221581] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    0.221587] pnp 00:00: [mem 0x40000000-0xf7ffffff window]
[    0.221593] pnp 00:00: [io  0x0d00-0xfdff window]
[    0.221599] pnp 00:00: [mem 0x00000000 window]
[    0.221605] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[    0.221737] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.222391] pnp 00:01: [io  0x0010-0x001f]
[    0.222398] pnp 00:01: [io  0x0024-0x0025]
[    0.222404] pnp 00:01: [io  0x0028-0x0029]
[    0.222409] pnp 00:01: [io  0x002c-0x002d]
[    0.222414] pnp 00:01: [io  0x0030-0x0031]
[    0.222420] pnp 00:01: [io  0x0034-0x0035]
[    0.222425] pnp 00:01: [io  0x0038-0x0039]
[    0.222431] pnp 00:01: [io  0x003c-0x003d]
[    0.222436] pnp 00:01: [io  0x0072-0x0077]
[    0.222441] pnp 00:01: [io  0x0080]
[    0.222446] pnp 00:01: [io  0x0090-0x009f]
[    0.222452] pnp 00:01: [io  0x00a4-0x00a5]
[    0.222457] pnp 00:01: [io  0x00a8-0x00a9]
[    0.222463] pnp 00:01: [io  0x00ac-0x00ad]
[    0.222468] pnp 00:01: [io  0x00b0-0x00b5]
[    0.222473] pnp 00:01: [io  0x00b8-0x00b9]
[    0.222479] pnp 00:01: [io  0x00bc-0x00bd]
[    0.222484] pnp 00:01: [io  0x0800-0x080f]
[    0.222490] pnp 00:01: [io  0x1000-0x107f]
[    0.222495] pnp 00:01: [io  0x1180-0x11bf]
[    0.222501] pnp 00:01: [io  0x002e-0x002f]
[    0.222506] pnp 00:01: [io  0x04d0-0x04d1]
[    0.222511] pnp 00:01: [io  0xfe00]
[    0.222517] pnp 00:01: [io  0x164e-0x174c]
[    0.222523] pnp 00:01: [mem 0xe0000000-0xefffffff]
[    0.222528] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[    0.222534] pnp 00:01: [mem 0xf8000000-0xfbffffff]
[    0.222540] pnp 00:01: [mem 0xfef00000-0xfeffffff]
[    0.222709] system 00:01: [io  0x0800-0x080f] has been reserved
[    0.222718] system 00:01: [io  0x1000-0x107f] has been reserved
[    0.222725] system 00:01: [io  0x1180-0x11bf] has been reserved
[    0.222732] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.222739] system 00:01: [io  0xfe00] has been reserved
[    0.222746] system 00:01: [io  0x164e-0x174c] has been reserved
[    0.222758] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.222765] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[    0.222773] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.222780] system 00:01: [mem 0xfef00000-0xfeffffff] has been reserved
[    0.222789] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.222818] pnp 00:02: [io  0x0000-0x000f]
[    0.222824] pnp 00:02: [io  0x0081-0x008f]
[    0.222830] pnp 00:02: [io  0x00c0-0x00df]
[    0.222836] pnp 00:02: [dma 4]
[    0.222910] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.222937] pnp 00:03: [io  0x00f0-0x00fe]
[    0.222955] pnp 00:03: [irq 13]
[    0.223029] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.223113] pnp 00:04: [io  0x0070-0x0071]
[    0.223126] pnp 00:04: [irq 8]
[    0.223206] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.223233] pnp 00:05: [io  0x0061]
[    0.223308] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.223374] pnp 00:06: [io  0x0060]
[    0.223380] pnp 00:06: [io  0x0064]
[    0.223392] pnp 00:06: [irq 1]
[    0.223473] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.223506] pnp 00:07: [irq 12]
[    0.223584] pnp 00:07: Plug and Play ACPI device, IDs PNP0f13 (active)
[    0.223889] pnp 00:08: [mem 0xff800000-0xffffffff]
[    0.223975] pnp 00:08: Plug and Play ACPI device, IDs INT0800 (active)
[    0.224459] pnp: PnP ACPI: found 9 devices
[    0.224464] ACPI: ACPI bus type pnp unregistered
[    0.224472] PnPBIOS: Disabled by ACPI PNP
[    0.265816] PCI: max bus depth: 1 pci_try_num: 2
[    0.265914] pci 0000:00:1c.3: BAR 14: assigned [mem 0x40000000-0x401fffff]
[    0.265926] pci 0000:00:1c.3: BAR 15: assigned [mem 0x40200000-0x403fffff 64bit pref]
[    0.265939] pci 0000:00:1c.3: BAR 13: assigned [io  0x3000-0x3fff]
[    0.265950] pci 0000:00:1c.2: BAR 15: assigned [mem 0x40400000-0x405fffff 64bit pref]
[    0.265961] pci 0000:00:1c.1: BAR 14: assigned [mem 0x40600000-0x407fffff]
[    0.265972] pci 0000:00:1c.1: BAR 15: assigned [mem 0x40800000-0x409fffff 64bit pref]
[    0.265983] pci 0000:00:1c.1: BAR 13: assigned [io  0x4000-0x4fff]
[    0.265994] pci 0000:00:1c.0: BAR 15: assigned [mem 0x40a00000-0x40bfffff 64bit pref]
[    0.266005] pci 0000:00:1c.0: BAR 13: assigned [io  0x5000-0x5fff]
[    0.266013] pci 0000:00:1c.0: PCI bridge to [bus 05-05]
[    0.266020] pci 0000:00:1c.0:   bridge window [io  0x5000-0x5fff]
[    0.266030] pci 0000:00:1c.0:   bridge window [mem 0xf0100000-0xf01fffff]
[    0.266040] pci 0000:00:1c.0:   bridge window [mem 0x40a00000-0x40bfffff 64bit pref]
[    0.266053] pci 0000:00:1c.1: PCI bridge to [bus 07-07]
[    0.266060] pci 0000:00:1c.1:   bridge window [io  0x4000-0x4fff]
[    0.266070] pci 0000:00:1c.1:   bridge window [mem 0x40600000-0x407fffff]
[    0.266080] pci 0000:00:1c.1:   bridge window [mem 0x40800000-0x409fffff 64bit pref]
[    0.266093] pci 0000:00:1c.2: PCI bridge to [bus 09-09]
[    0.266100] pci 0000:00:1c.2:   bridge window [io  0x2000-0x2fff]
[    0.266110] pci 0000:00:1c.2:   bridge window [mem 0xf0200000-0xf02fffff]
[    0.266119] pci 0000:00:1c.2:   bridge window [mem 0x40400000-0x405fffff 64bit pref]
[    0.266132] pci 0000:00:1c.3: PCI bridge to [bus 0b-0b]
[    0.266139] pci 0000:00:1c.3:   bridge window [io  0x3000-0x3fff]
[    0.266149] pci 0000:00:1c.3:   bridge window [mem 0x40000000-0x401fffff]
[    0.266159] pci 0000:00:1c.3:   bridge window [mem 0x40200000-0x403fffff 64bit pref]
[    0.266172] pci 0000:00:1e.0: PCI bridge to [bus 11-11]
[    0.266226] pci 0000:00:1c.0: setting latency timer to 64
[    0.266239] pci 0000:00:1c.1: enabling device (0000 -> 0003)
[    0.266263] pci 0000:00:1c.1: setting latency timer to 64
[    0.266290] pci 0000:00:1c.2: setting latency timer to 64
[    0.266302] pci 0000:00:1c.3: enabling device (0000 -> 0003)
[    0.266325] pci 0000:00:1c.3: setting latency timer to 64
[    0.266340] pci 0000:00:1e.0: setting latency timer to 64
[    0.266349] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.266355] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[    0.266362] pci_bus 0000:00: resource 6 [mem 0x000d0000-0x000d3fff]
[    0.266368] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff]
[    0.266374] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff]
[    0.266381] pci_bus 0000:00: resource 9 [mem 0x000e0000-0x000e3fff]
[    0.266387] pci_bus 0000:00: resource 10 [mem 0x40000000-0xf7ffffff]
[    0.266393] pci_bus 0000:00: resource 11 [io  0x0d00-0xfdff]
[    0.266400] pci_bus 0000:05: resource 0 [io  0x5000-0x5fff]
[    0.266406] pci_bus 0000:05: resource 1 [mem 0xf0100000-0xf01fffff]
[    0.266413] pci_bus 0000:05: resource 2 [mem 0x40a00000-0x40bfffff 64bit pref]
[    0.266419] pci_bus 0000:07: resource 0 [io  0x4000-0x4fff]
[    0.266426] pci_bus 0000:07: resource 1 [mem 0x40600000-0x407fffff]
[    0.266432] pci_bus 0000:07: resource 2 [mem 0x40800000-0x409fffff 64bit pref]
[    0.266439] pci_bus 0000:09: resource 0 [io  0x2000-0x2fff]
[    0.266445] pci_bus 0000:09: resource 1 [mem 0xf0200000-0xf02fffff]
[    0.266451] pci_bus 0000:09: resource 2 [mem 0x40400000-0x405fffff 64bit pref]
[    0.266458] pci_bus 0000:0b: resource 0 [io  0x3000-0x3fff]
[    0.266464] pci_bus 0000:0b: resource 1 [mem 0x40000000-0x401fffff]
[    0.266471] pci_bus 0000:0b: resource 2 [mem 0x40200000-0x403fffff 64bit pref]
[    0.266478] pci_bus 0000:11: resource 4 [io  0x0000-0x0cf7]
[    0.266484] pci_bus 0000:11: resource 5 [mem 0x000a0000-0x000bffff]
[    0.266490] pci_bus 0000:11: resource 6 [mem 0x000d0000-0x000d3fff]
[    0.266497] pci_bus 0000:11: resource 7 [mem 0x000d4000-0x000d7fff]
[    0.266503] pci_bus 0000:11: resource 8 [mem 0x000d8000-0x000dbfff]
[    0.266509] pci_bus 0000:11: resource 9 [mem 0x000e0000-0x000e3fff]
[    0.266516] pci_bus 0000:11: resource 10 [mem 0x40000000-0xf7ffffff]
[    0.266522] pci_bus 0000:11: resource 11 [io  0x0d00-0xfdff]
[    0.266653] NET: Registered protocol family 2
[    0.272718] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.273259] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.274183] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.274611] TCP: Hash tables configured (established 131072 bind 65536)
[    0.274617] TCP reno registered
[    0.274626] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.274645] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.274889] NET: Registered protocol family 1
[    0.274926] pci 0000:00:02.0: Boot video device
[    0.275232] PCI: CLS 32 bytes, default 64
[    0.275358] Unpacking initramfs...
[    0.766324] Freeing initrd memory: 9916k freed
[    0.773864] Simple Boot Flag at 0x36 set to 0x1
[    0.774838] audit: initializing netlink socket (disabled)
[    0.774862] type=2000 audit(1416738258.768:1): initialized
[    0.802892] highmem bounce pool size: 64 pages
[    0.802904] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.803636] VFS: Disk quotas dquot_6.5.2
[    0.803704] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.803846] msgmni has been set to 1751
[    0.804288] alg: No test for stdrng (krng)
[    0.804366] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.804373] io scheduler noop registered
[    0.804378] io scheduler deadline registered
[    0.804413] io scheduler cfq registered (default)
[    0.804597] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.804677] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    0.804817] pcieport 0000:00:1c.1: setting latency timer to 64
[    0.804887] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[    0.805014] pcieport 0000:00:1c.2: setting latency timer to 64
[    0.805083] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[    0.805210] pcieport 0000:00:1c.3: setting latency timer to 64
[    0.805279] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
[    0.805465] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.805516] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.805521] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.806267] intel_idle: MWAIT substates: 0x20220
[    0.806285] intel_idle: v0.4 model 0x1C
[    0.806290] intel_idle: lapic_timer_reliable_states 0x2
[    0.806296] Marking TSC unstable due to TSC halts in idle states deeper than C2
[    0.806366] ERST: Table is not found!
[    0.806370] GHES: HEST is not enabled!
[    0.806404] isapnp: Scanning for PnP cards...
[    1.160184] isapnp: No Plug & Play device found
[    1.160352] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.164721] Linux agpgart interface v0.103
[    1.164955] agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
[    1.165079] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[    1.165248] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[    1.165497] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    1.165847] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[    1.220963] i8042: Detected active multiplexing controller, rev 1.1
[    1.243930] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.243946] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.244054] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.244139] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.244210] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.244541] mousedev: PS/2 mouse device common for all mice
[    1.246057] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    1.246101] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.246223] cpuidle: using governor ladder
[    1.246358] cpuidle: using governor menu
[    1.246888] TCP cubic registered
[    1.247015] NET: Registered protocol family 10
[    1.248287] Mobile IPv6
[    1.248295] NET: Registered protocol family 17
[    1.248306] Registering the dns_resolver key type
[    1.248348] Using IPI No-Shortcut mode
[    1.248702] PM: Hibernation image not present or could not be loaded.
[    1.248730] registered taskstats version 1
[    1.249571] rtc_cmos 00:04: setting system clock to 2014-11-23 10:24:20 UTC (1416738260)
[    1.249705] Initializing network drop monitor service
[    1.249957] Freeing unused kernel memory: 420k freed
[    1.250288] Write protecting the kernel text: 2860k
[    1.250369] Write protecting the kernel read-only data: 1084k
[    1.250375] NX-protecting the kernel data: 3284k
[    1.278409] udevd[49]: starting version 175
[    1.306086] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.375759] sky2: driver version 1.30
[    1.376043] sky2 0000:09:00.0: setting latency timer to 64
[    1.396411] sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0
[    1.397026] sky2 0000:09:00.0: irq 44 for MSI/MSI-X
[    1.432092] sky2 0000:09:00.0: eth0: addr 00:24:54:44:c4:f4
[    1.436849] usbcore: registered new interface driver usbfs
[    1.436913] usbcore: registered new interface driver hub
[    1.438529] thermal LNXTHERM:00: registered as thermal_zone0
[    1.438538] ACPI: Thermal Zone [TZ00] (18 C)
[    1.450554] usbcore: registered new device driver usb
[    1.451926] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.452074] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    1.452086] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.452158] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    1.452213] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    1.452237] ehci_hcd 0000:00:1d.7: debug port 1
[    1.456133] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    1.477069] uhci_hcd: USB Universal Host Controller Interface driver
[    1.477197] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf0604000
[    1.496063] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.496137] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.496147] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.496156] usb usb1: Product: EHCI Host Controller
[    1.496163] usb usb1: Manufacturer: Linux 3.2.0-4-686-pae ehci_hcd
[    1.496170] usb usb1: SerialNumber: 0000:00:1d.7
[    1.496588] hub 1-0:1.0: USB hub found
[    1.496605] hub 1-0:1.0: 8 ports detected
[    1.497797] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.497811] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.497846] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.497902] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[    1.498019] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.498028] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.498037] usb usb2: Product: UHCI Host Controller
[    1.498044] usb usb2: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    1.498051] usb usb2: SerialNumber: 0000:00:1d.0
[    1.498491] hub 2-0:1.0: USB hub found
[    1.498510] hub 2-0:1.0: 2 ports detected
[    1.498775] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.498787] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.498819] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.498908] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[    1.499017] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.499026] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.499034] usb usb3: Product: UHCI Host Controller
[    1.499040] usb usb3: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    1.499047] usb usb3: SerialNumber: 0000:00:1d.1
[    1.499465] hub 3-0:1.0: USB hub found
[    1.499482] hub 3-0:1.0: 2 ports detected
[    1.499741] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.499753] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.499782] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.499874] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[    1.499986] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.499996] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.500041] usb usb4: Product: UHCI Host Controller
[    1.500048] usb usb4: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    1.500055] usb usb4: SerialNumber: 0000:00:1d.2
[    1.501090] hub 4-0:1.0: USB hub found
[    1.501109] hub 4-0:1.0: 2 ports detected
[    1.501377] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.501389] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.501427] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.501517] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[    1.501629] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.501638] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.501646] usb usb5: Product: UHCI Host Controller
[    1.501653] usb usb5: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    1.501660] usb usb5: SerialNumber: 0000:00:1d.3
[    1.502083] hub 5-0:1.0: USB hub found
[    1.502100] hub 5-0:1.0: 2 ports detected
[    1.526916] SCSI subsystem initialized
[    1.548584] libata version 3.00 loaded.
[    1.551083] ahci 0000:00:1f.2: version 3.0
[    1.551217] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[    1.551380] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    1.551392] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
[    1.551406] ahci 0000:00:1f.2: setting latency timer to 64
[    1.555262] scsi0 : ahci
[    1.555651] scsi1 : ahci
[    1.555935] scsi2 : ahci
[    1.556327] scsi3 : ahci
[    1.556828] ata1: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604500 irq 45
[    1.556841] ata2: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604580 irq 45
[    1.556852] ata3: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604600 irq 45
[    1.556863] ata4: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604680 irq 45
[    1.876151] ata2: SATA link down (SStatus 0 SControl 300)
[    1.876196] ata3: SATA link down (SStatus 0 SControl 300)
[    1.876236] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.876274] ata4: SATA link down (SStatus 0 SControl 300)
[    1.882326] ata1.00: ATA-8: SAMSUNG HM160HI, HH100-06, max UDMA7
[    1.882341] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.888542] ata1.00: configured for UDMA/133
[    1.888810] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM160HI  HH10 PQ: 0 ANSI: 5
[    1.900853] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.901076] sd 0:0:0:0: [sda] Write Protect is off
[    1.901086] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.901183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.920105] usb 1-8: new high-speed USB device number 3 using ehci_hcd
[    1.939228]  sda: sda1 sda2 sda3
[    1.940384] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.944474] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.071272] usb 1-8: New USB device found, idVendor=0ac8, idProduct=c33f
[    2.071285] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.071294] usb 1-8: Product: WebCam SCB-0340N
[    2.071302] usb 1-8: Manufacturer: Namuga.
[    2.312070] usb 4-2: new full-speed USB device number 2 using uhci_hcd
[    2.485988] usb 4-2: New USB device found, idVendor=0a5c, idProduct=219b
[    2.486004] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.486011] usb 4-2: Product: Broadcom Bluetooth 2.1 Device
[    2.486016] usb 4-2: Manufacturer: Broadcom Corp
[    2.486021] usb 4-2: SerialNumber: 0026B6B28DB2
[    2.538171] PM: Starting manual resume from disk
[    2.538180] PM: Hibernation image partition 8:2 present
[    2.538184] PM: Looking for hibernation image.
[    2.538549] PM: Image not found (code -22)
[    2.538554] PM: Hibernation image not present or could not be loaded.
[    2.599269] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    4.283050] udevd[335]: starting version 175
[    5.183461] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[    5.183551] ACPI: Lid Switch [LID0]
[    5.183776] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    5.183793] ACPI: Power Button [PWRB]
[    5.184082] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[    5.184098] ACPI: Sleep Button [SLPB]
[    5.184316] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[    5.184330] ACPI: Power Button [PWRF]
[    5.229488] ACPI: Requesting acpi_cpufreq
[    5.353438] iTCO_vendor_support: vendor-support=0
[    5.355247] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    5.355506] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x1060)
[    5.355666] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    5.425615] samsung_laptop: Backlight controlled by ACPI video driver
[    5.472809] cfg80211: Calling CRDA to update world regulatory domain
[    5.482756] ACPI: AC Adapter [ADP1] (on-line)
[    5.489918] ACPI: Battery Slot [BAT1] (battery present)
[    5.586506] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    5.829742] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[    5.829823] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[    5.936554] [drm] Initialized drm 1.1.0 20060810
[    6.027290] ath9k 0000:05:00.0: setting latency timer to 64
[    6.078924] ath: EEPROM regdomain: 0x65
[    6.078932] ath: EEPROM indicates we should expect a direct regpair map
[    6.078942] ath: Country alpha2 being used: 00
[    6.078947] ath: Regpair used: 0x65
[    6.117116] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    6.118673] Registered led device: ath9k-phy0
[    6.118690] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xf8600000, irq=16
[    6.279427] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[    6.279742] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[    6.281473] i915 0000:00:02.0: setting latency timer to 64
[    6.336816] i915 0000:00:02.0: irq 47 for MSI/MSI-X
[    6.336844] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    6.336851] [drm] Driver supports precise vblank timestamp query.
[    6.336955] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem :o wns=io+mem
[    6.693839] [drm] initialized overlay support
[    6.713649] fbcon: inteldrmfb (fb0) is primary device
[    6.812445] cfg80211: World regulatory domain updated:
[    6.812452] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    6.812459] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    6.812464] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    6.812469] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[    6.812475] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[    6.812480] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[    6.812485] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[    6.812490] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[    6.812496] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[    7.016170] Bluetooth: Core ver 2.16
[    7.016238] NET: Registered protocol family 31
[    7.016244] Bluetooth: HCI device and connection manager initialized
[    7.016251] Bluetooth: HCI socket layer initialized
[    7.016257] Bluetooth: L2CAP socket layer initialized
[    7.016489] Bluetooth: SCO socket layer initialized
[    7.043657] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    7.044818] usbcore: registered new interface driver btusb
[    7.164536] Console: switching to colour frame buffer device 128x37
[    7.172192] fb0: inteldrmfb frame buffer device
[    7.172196] drm: registered panic notifier
[    7.173435] ACPI Warning: _BQC returned an invalid level (20110623/video-518)
[    7.174076] acpi device:03: registered as cooling_device2
[    7.174432] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
[    7.174590] ACPI: Video Device [IGD0] (multi-head: yes  rom: no  post: no)
[    7.174667] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    7.426391] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04773/0xa40000/0xa0000
[    7.544052] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input9
[    7.708989] Linux media interface: v0.10
[    7.722474] Linux video capture interface: v2.00
[    7.769076] uvcvideo: Found UVC 1.00 device WebCam SCB-0340N (0ac8:c33f)
[    7.771359] input: WebCam SCB-0340N as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input10
[    7.771625] usbcore: registered new interface driver uvcvideo
[    7.771632] USB Video Class driver (1.1.1)
[   10.130725] Adding 1952764k swap on /dev/sda2.  Priority:-1 extents:1 across:1952764k 
[   10.182546] EXT4-fs (sda1): re-mounted. Opts: (null)
[   10.606543] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   10.772364] loop: module loaded
[   12.281595] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[   13.728638] RPC: Registered named UNIX socket transport module.
[   13.728647] RPC: Registered udp transport module.
[   13.728654] RPC: Registered tcp transport module.
[   13.728659] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   13.782375] FS-Cache: Loaded
[   13.844658] FS-Cache: Netfs 'nfs' registered for caching
[   13.870185] Installing knfsd (copyright (C) 1996 [EMAIL="[email protected]"][email protected][/EMAIL]).
[   16.351108] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input11
[   17.985721] Bluetooth: RFCOMM TTY layer initialized
[   17.985738] Bluetooth: RFCOMM socket layer initialized
[   17.985745] Bluetooth: RFCOMM ver 1.11
[   18.052228] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   18.052238] Bluetooth: BNEP filters: protocol multicast
[   18.377748] lp: driver loaded but no devices found
[   18.411811] ppdev: user-space parallel port driver
[   19.502623] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.563696] sky2 0000:09:00.0: eth0: enabling interface
[   19.564710] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   61.072081] usb 1-3: new high-speed USB device number 4 using ehci_hcd
[   61.209166] usb 1-3: New USB device found, idVendor=12d1, idProduct=14fe
[   61.209179] usb 1-3: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[   61.209188] usb 1-3: Product: HUAWEI Mobile
[   61.209196] usb 1-3: Manufacturer: HUAWEI Technology
[   61.437609] Initializing USB Mass Storage driver...
[   61.438338] scsi4 : usb-storage 1-3:1.0
[   61.438869] scsi5 : usb-storage 1-3:1.1
[   61.439114] usbcore: registered new interface driver usb-storage
[   61.439122] USB Mass Storage support registered.
[   62.325110] usb 1-3: USB disconnect, device number 4
[   62.700080] usb 1-3: new high-speed USB device number 5 using ehci_hcd
[   62.833797] usb 1-3: New USB device found, idVendor=12d1, idProduct=1506
[   62.833814] usb 1-3: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[   62.833822] usb 1-3: Product: HUAWEI Mobile
[   62.833829] usb 1-3: Manufacturer: HUAWEI Technology
[   62.856522] scsi6 : usb-storage 1-3:1.2
[   62.861946] scsi7 : usb-storage 1-3:1.3
[   63.078179] usbcore: registered new interface driver usbserial
[   63.078227] USB Serial support registered for generic
[   63.079055] usbcore: registered new interface driver usbserial_generic
[   63.079065] usbserial: USB Serial Driver core
[   63.096565] USB Serial support registered for GSM modem (1-port)
[   63.097920] option 1-3:1.0: GSM modem (1-port) converter detected
[   63.098450] usb 1-3: GSM modem (1-port) converter now attached to ttyUSB0
[   63.099585] usbcore: registered new interface driver option
[   63.099594] option: v0.7.2:USB Driver for GSM modems
[   63.857115] scsi 6:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[   63.862725] scsi 6:0:0:0: Attached scsi generic sg1 type 5
[   63.864448] scsi 7:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
[   63.867036] sd 7:0:0:0: Attached scsi generic sg2 type 0
[   63.870343] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[   63.948579] sr0: scsi-1 drive
[   63.948591] cdrom: Uniform CD-ROM driver Revision: 3.20
[   63.949929] sr 6:0:0:0: Attached scsi CD-ROM sr0
[   71.656456] ISO 9660 Extensions: Microsoft Joliet Level 1
[   71.690626] ISOFS: changing to secondary root
[   77.993273] PPP generic driver version 2.4.2

: 23 listopada 2014, 14:02
autor: ryba84
A zainstalowałeś screen? I uruchomiłeś przed wywołaniem tych poleceń

Kod: Zaznacz cały

screen /dev/ttyUSB0
?

: 23 listopada 2014, 15:03
autor: Henk100
A no właśnie, tu ciekawa rzecz. Mam wgrany screen ale gdy używam tej komendy, to wyskakuje komunikat, że nie ma takiego pliku, ani katalogu

Ps.

Ok. Znalazłem rozwiązanie. Dziękuję za pomoc!