[+] LinSSID, graficzny skaner wifi - instalacja na Jessie. - Polskie Forum Użytkowników Debiana

[+] LinSSID, graficzny skaner wifi - instalacja na Jessie.

Posty: 9 • Strona 1 z 1

Matrixx: Beginner; Posty: 235; Rejestracja: 03 maja 2016, 16:30

[+] LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: Matrixx » 02 lipca 2016, 23:55

Potrzebuje skaner wifi dla Jessie, znalazlem LinSSD: https://www.unixmen.com/linssid-graphic ... ner-linux/
Niestety nie moge zainstalowac ani z paczki .deb ani z ppa dla Ubuntu. Help.
To nie musi koniecznie byc LinSSD, kazdy inny graficzny tez moze byc, byle dawal minimum niezbednych informacji.
Pozdrawiam

Kod: Zaznacz cały

root@debian:/home/robin# uname -a
Linux debian 4.5.0-0.slh.1-aptosid-amd64 #1 SMP PREEMPT aptosid 4.5-1 (2016-03-14) x86_64 GNU/Linux

Kod: Zaznacz cały

root@debian:/home/robin# lsb_release -a
No LSB modules are available.
Distributor ID:	Debian
Description:	Debian GNU/Linux 8.4 (jessie)
Release:	8.4
Codename:	jessie

Kod: Zaznacz cały

root@debian:/home/robin# lspci -k
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (external gfx0 port B) (rev 02)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (external gfx0 port B)
00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port B)
	Kernel driver in use: pcieport
00:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port D)
	Kernel driver in use: pcieport
00:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port E)
	Kernel driver in use: pcieport
00:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port F)
	Kernel driver in use: pcieport
00:07.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port G)
	Kernel driver in use: pcieport
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40)
	Subsystem: ASUSTeK Computer Inc. Device 84dd
	Kernel driver in use: ahci
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Kernel driver in use: ohci-pci
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Kernel driver in use: ehci-pci
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Kernel driver in use: ohci-pci
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Kernel driver in use: ehci-pci
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller (rev 42)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller
	Kernel driver in use: piix4_smbus
00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 IDE Controller (rev 40)
	Subsystem: ASUSTeK Computer Inc. Device 84de
	Kernel driver in use: pata_atiixp
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) (rev 40)
	Subsystem: ASUSTeK Computer Inc. Device 84fb
	Kernel driver in use: snd_hda_intel
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge (rev 40)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
	Kernel driver in use: ohci-pci
00:16.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Kernel driver in use: ohci-pci
00:16.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Kernel driver in use: ehci-pci
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 0
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 3
	Kernel driver in use: k10temp
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 4
	Kernel driver in use: fam15h_power
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 5
01:00.0 VGA compatible controller: NVIDIA Corporation NV42GL [Quadro FX 3450/4000 SDI] (rev a2)
	Subsystem: NVIDIA Corporation Device 029b
	Kernel driver in use: nouveau
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 09)
	Subsystem: ASUSTeK Computer Inc. P8 series motherboard
	Kernel driver in use: r8169
03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller
	Subsystem: ASUSTeK Computer Inc. P8B WS Motherboard
	Kernel driver in use: xhci_hcd
04:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01)
	Subsystem: ASUSTeK Computer Inc. Device 84b7
	Kernel driver in use: ahci
05:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller
	Subsystem: ASUSTeK Computer Inc. P8B WS Motherboard
	Kernel driver in use: xhci_hcd
06:05.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 0a)
	Subsystem: Creative Labs CT4780 SBLive! Value
	Kernel driver in use: snd_emu10k1
06:05.1 Input device controller: Creative Labs SB Live! Game Port (rev 0a)
	Subsystem: Creative Labs Gameport Joystick
	Kernel driver in use: Emu10k1_gameport

Kod: Zaznacz cały

root@debian:/home/robin# lsusb
Bus 006 Device 002: ID 0cf3:9271 Atheros Communications, Inc. AR9271 802.11n
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 009 Device 002: ID 1241:1177 Belkin F8E842-DL Mouse
Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 003: ID 062a:4101 Creative Labs 
Bus 008 Device 002: ID 1c4f:0024 SiGma Micro 
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Kod: Zaznacz cały

root@debian:/home/robin# ifconfig
eth0      Link encap:Ethernet  HWaddr 60:a4:4c:64:a8:bd  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:14918 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8420 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:15438372 (14.7 MiB)  TX bytes:1434468 (1.3 MiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:45 errors:0 dropped:0 overruns:0 frame:0
          TX packets:45 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:14051 (13.7 KiB)  TX bytes:14051 (13.7 KiB)

virbr1    Link encap:Ethernet  HWaddr 52:54:00:52:78:c3  
          inet addr:192.168.100.1  Bcast:192.168.100.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:198 (198.0 B)

virbr1-nic Link encap:Ethernet  HWaddr 52:54:00:52:78:c3  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:500 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan1     Link encap:Ethernet  HWaddr b0:48:7a:8c:72:1a  
          inet addr:192.168.0.37  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: 2a02:8084:ac0:b00:b248:7aff:fe8c:721a/128 Scope:Global
          inet6 addr: fe80::b248:7aff:fe8c:721a/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:56196 errors:0 dropped:0 overruns:0 frame:0
          TX packets:39468 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:61518427 (58.6 MiB)  TX bytes:4982054 (4.7 MiB)

Kod: Zaznacz cały

root@debian:/home/robin# iw list
Wiphy phy0
	max # scan SSIDs: 4
	max scan IEs length: 2257 bytes
	Retry short limit: 7
	Retry long limit: 4
	Coverage class: 0 (up to 0m)
	Device supports RSN-IBSS.
	Device supports T-DLS.
	Supported Ciphers:
		* WEP40 (00-0f-ac:1)
		* WEP104 (00-0f-ac:5)
		* TKIP (00-0f-ac:2)
		* CCMP (00-0f-ac:4)
		* 00-0f-ac:10
		* GCMP (00-0f-ac:8)
		* 00-0f-ac:9
		* CMAC (00-0f-ac:6)
		* 00-0f-ac:13
		* 00-0f-ac:11
		* 00-0f-ac:12
	Available Antennas: TX 0x1 RX 0x1
	Configured Antennas: TX 0x1 RX 0x1
	Supported interface modes:
		 * IBSS
		 * managed
		 * AP
		 * AP/VLAN
		 * monitor
		 * mesh point
		 * P2P-client
		 * P2P-GO
		 * Unknown mode (11)
	Band 1:
		Capabilities: 0x116e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT TX/RX MCS rate indexes supported: 0-7
		Bitrates (non-HT):
			* 1.0 Mbps
			* 2.0 Mbps (short preamble supported)
			* 5.5 Mbps (short preamble supported)
			* 11.0 Mbps (short preamble supported)
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
		Frequencies:
			* 2412 MHz [1] (20.0 dBm)
			* 2417 MHz [2] (20.0 dBm)
			* 2422 MHz [3] (20.0 dBm)
			* 2427 MHz [4] (20.0 dBm)
			* 2432 MHz [5] (20.0 dBm)
			* 2437 MHz [6] (20.0 dBm)
			* 2442 MHz [7] (20.0 dBm)
			* 2447 MHz [8] (20.0 dBm)
			* 2452 MHz [9] (20.0 dBm)
			* 2457 MHz [10] (20.0 dBm)
			* 2462 MHz [11] (20.0 dBm)
			* 2467 MHz [12] (20.0 dBm)
			* 2472 MHz [13] (20.0 dBm)
			* 2484 MHz [14] (disabled)
	Supported commands:
		 * new_interface
		 * set_interface
		 * new_key
		 * start_ap
		 * new_station
		 * new_mpath
		 * set_mesh_config
		 * set_bss
		 * authenticate
		 * associate
		 * deauthenticate
		 * disassociate
		 * join_ibss
		 * join_mesh
		 * remain_on_channel
		 * set_tx_bitrate_mask
		 * frame
		 * frame_wait_cancel
		 * set_wiphy_netns
		 * set_channel
		 * set_wds_peer
		 * tdls_mgmt
		 * tdls_oper
		 * probe_client
		 * set_noack_map
		 * register_beacons
		 * start_p2p_device
		 * set_mcast_rate
		 * testmode
		 * channel_switch
		 * Unknown command (104)
		 * connect
		 * disconnect
	Supported TX frame types:
		 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
	Supported RX frame types:
		 * IBSS: 0x40 0xb0 0xc0 0xd0
		 * managed: 0x40 0xd0
		 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * mesh point: 0xb0 0xc0 0xd0
		 * P2P-client: 0x40 0xd0
		 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * P2P-device: 0x40 0xd0
	software interface modes (can always be added):
		 * AP/VLAN
		 * monitor
	valid interface combinations:
		 * #{ managed, P2P-client } <= 2, #{ AP, mesh point, P2P-GO } <= 2,
		   total <= 2, #channels <= 1
	HT Capability overrides:
		 * MCS: ff ff ff ff ff ff ff ff ff ff
		 * maximum A-MSDU length
		 * supported channel width
		 * short GI for 40 MHz
		 * max A-MPDU length exponent
		 * min MPDU start spacing
	Device supports TX status socket option.
	Device supports HT-IBSS.
	Device supports SAE with AUTHENTICATE command
	Device supports low priority scan.
	Device supports scan flush.
	Device supports AP scan.
	Device supports per-vif TX power setting
	Driver supports full state transitions for AP/GO clients
	Driver supports a userspace MPM
	Device supports ACK timeout estimation.

Objawy:

Po instalacji odpalam LinSSID, pojawia sie komunikat z zadaniem:

Kod: Zaznacz cały

Password required for iwlist scan

Podaje haslo admina.
Nastepny komunikat:

Kod: Zaznacz cały

Bad Stuff. Cannot find interface pipe

Komunikat znika.
W Internecie nie ma za wiele na ten temat, niestety.

Dodatkowo:
Na tej stronie: http://jcabezuelo.blogspot.ie/2014/01/s ... al-de.html
radza zainstalowac iw :

Kod: Zaznacz cały

sudo cat /proc/net/wireless
sudo apt-get install iw
sudo iw list

Zainstalowalem, nie pomoglo.

Ostatnio zmieniony 03 lipca 2016, 17:42 przez marcin1982, łącznie zmieniany 3 razy.
Powód: Rozwiązane tematy oznaczamy [+] - nie [SOLVED] ...

dedito: Moderator; Posty: 3560; Rejestracja: 18 listopada 2013, 21:07; Lokalizacja: Gliwice

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: dedito » 03 lipca 2016, 00:13

Masz w backportach.

Matrixx: Beginner; Posty: 235; Rejestracja: 03 maja 2016, 16:30

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: Matrixx » 03 lipca 2016, 01:24

Wiem. Moje zrodla:

Kod: Zaznacz cały

  GNU nano 2.2.6          File: /etc/apt/sources.list                           

# 

# deb cdrom:[Debian GNU/Linux 8.3.0 _Jessie_ - Official amd64 NETINST Binary-1 $

#deb cdrom:[Debian GNU/Linux 8.3.0 _Jessie_ - Official amd64 NETINST Binary-1 2$

deb http://ftp.de.debian.org/debian/ jessie main
deb-src http://ftp.de.debian.org/debian/ jessie main

deb http://security.debian.org/ jessie/updates main
deb-src http://security.debian.org/ jessie/updates main

# jessie-updates, previously known as 'volatile'
deb http://ftp.de.debian.org/debian/ jessie-updates main
deb-src http://ftp.de.debian.org/debian/ jessie-updates main

deb http://ftp.debian.org/debian jessie-backports main
deb http://aptosid.com/debian unstable main fix.main

Niestety kiedy chce uruchomic po raz pierwszy to dostaje komunikat:

Kod: Zaznacz cały

Unable to continue. Cannot find interface pipe

dedito: Moderator; Posty: 3560; Rejestracja: 18 listopada 2013, 21:07; Lokalizacja: Gliwice

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: dedito » 03 lipca 2016, 13:09

Daj jeszcze wyniki:

Kod: Zaznacz cały

sudo cat /proc/net/wireless
sudo iw dev

Próbowałeś uruchomić ten skaner z konta root?

Matrixx: Beginner; Posty: 235; Rejestracja: 03 maja 2016, 16:30

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: Matrixx » 03 lipca 2016, 15:43

Kod: Zaznacz cały

root@debian:/home/robin# cat /proc/net/wireless
Inter-| sta-|   Quality        |   Discarded packets               | Missed | WE
 face | tus | link level noise |  nwid  crypt   frag  retry   misc | beacon | 22
 wlan1: 0000   70.  -36.  -256        0      0      0      0     71        0

Kod: Zaznacz cały

root@debian:/home/robin# iw dev
phy#1
	Interface wlan1
		ifindex 6
		wdev 0x100000001
		addr b0:48:7a:8c:72:1a
		type managed
		channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz

Uruchomienie z konta root niczego nie zmienia.

dedito: Moderator; Posty: 3560; Rejestracja: 18 listopada 2013, 21:07; Lokalizacja: Gliwice

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: dedito » 03 lipca 2016, 17:10

Gdy uruchamiasz z konta root to dalej masz ten komunikat ?

Kod: Zaznacz cały

Password required for iwlist scan

Spróbuj uruchomić tak:

Kod: Zaznacz cały

gksu linssid

Matrixx: Beginner; Posty: 235; Rejestracja: 03 maja 2016, 16:30

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: Matrixx » 03 lipca 2016, 17:27

"dedito" jestes genialnialny !!! Dziala, po komendzie:

Kod: Zaznacz cały

gksu linssid

Jak to nalezy rozumiec, co ta komenda zmienila?

dedito: Moderator; Posty: 3560; Rejestracja: 18 listopada 2013, 21:07; Lokalizacja: Gliwice

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: dedito » 03 lipca 2016, 17:33

Najwyraźniej nie masz dopisane nic pod kątem linssid do sudoers..
Przeczytaj jeszcze man linssid, tam jest opisane jak dodać wpis w sudoers i wtedy powinno działać normalnie.
gksu to jest graficzny odpowienik sudo.

Matrixx: Beginner; Posty: 235; Rejestracja: 03 maja 2016, 16:30

Re: LinSSID, graficzny skaner wifi - instalacja na Jessie.

Post autor: Matrixx » 03 lipca 2016, 17:39

Dziekuje za rozwiazanie problemu.

Zablokowany

Posty: 9 • Strona 1 z 1

Wróć do „Sieci”